NSK MEGATORQUE MOTOR SYSTEM User Manual Download Page 11

Page: 11 / 44

2. Specification

— 2-5 —

2.2.2.2. CN2 Signal List

Table 2-3: Signal name and function (shipping set)

No.

Port

code

Signal

code

Contact

logic

Signal function

Function

- DC24

24 VDC external power

supply

External power supply for input signal

- -

Do not connect

PI0 EMST

Normaly

closed

Emergency stop

Interrupts the positioning and stops with the dynamic
brake

PI1 ACLR

Normaly

open

Alarm clear

Clears warning

PI2 OTP

Normaly

closed

Travel limit, + direction

If OTP input goes active, the Motor servo is locked in
the CW only

PI3 OTM

Normaly

closed

Travel limit, - direction

If OTM input goes active, the Motor servo is locked in
the CCW only

Do not connect

PO0 DRDY

Positive

Driver Unit ready

Reports that the Motor is ready to rotate (Those pins
open when Motor is not ready, or an alarm occurs)

Do not connect

- COM

Output signal COMMON

Common for output signal

！

Caution : Be sure to follow the operation manual when your Megatorque Motor

System is a custom-made version and the function of Input/Output signals
are specially arranged.

！

Caution : Never connect the pins indicated as “Do not connect” Be sure to connect

these pins of the master controller (PLC, etc) side after you have connected
all pins of the CN2 connector. Otherwise, it may result in a malfunction or
breakdown of the system.

Summary of Contents for MEGATORQUE MOTOR SYSTEM













































Search results

Summary of Contents for MEGATORQUE MOTOR SYSTEM

Reviews:

Related manuals for MEGATORQUE MOTOR SYSTEM

Brands by name

Popular brands

NSK MEGATORQUE MOTOR SYSTEM, User Manual

Search results

Summary of Contents for MEGATORQUE MOTOR SYSTEM

Reviews:

Related manuals for MEGATORQUE MOTOR SYSTEM

Brands by name

Popular brands