background image

WARRANTY

NSI Corporation Limited Warranty 

NSI Corporation warrants new electronics products to be free from defective materials and workmanship for a
period of one (1) year from the date of purchase to the original owner when purchased from an authorized NSI
dealer.

The purchaser is responsible for completing and mailing to NSI, within 15 days of purchase, the warranty registration
card enclosed with each product.  NSI products that have been subject to accident, alteration, abuse, or defacing
of the serial number are not covered by this warranty.  The normal wear and tear of items such  as knobs, jacks,
and switches are not covered under this warranty.

If your NSI product requires service during the warranty period, NSI will repair or replace, at its option, defective
materials provided you have identified yourself as the original owner of the product to NSI or any authorized NSI
dealer.  Transportation charges to and from an authorized dealer or the NSI factory for repair shall be the responsibility
of the owner.  All products returned to NSI must have factory authorization for return prior to shipping.

NSI Corporation is not liable for any incidental or consequential damages resulting from defect or failure other
than repairs of the NSI product subject to the terms of this warranty.  This warranty gives you specific legal rights,
and you may have other rights which vary from state to state.  This warranty is expressly in lieu  of all other
agreements and warranties expressed or implied except as may be otherwise required by law.

REMOTE CONTROL PANEL

OPERATION 

Software Revision 3.00, Version C

NSI Corporation Limited Warranty 

NSI CORPORATION

8

Summary of Contents for 804CP









Reviews: