background image

 

 

 

©Novinium, Inc. 2016, all rights reserved. 

 

NRI 603 – Small Diameter Cables  – SPR 

Revised: February 19, 2016 

 

Page 

6

 of 

11

 

 

Record all fluid and water flush and enter 
the total volume into Knomentous. 

3.

 

Read the liquid flow meter. 

 

The liquid flow meter shows the volume of fluid flowing through the glass tube every minute. It does 
this by moving the two small BBs (one black, one silver) in the liquid flow meter’s glass tube. 

 

The black BB is tinted black glass, while the silver BB is stainless steel. The black BB is more sensitive to 
flow than the silver ball and must be located above the silver BB. 

 

If the BBs are reversed, clearly label and contact supply chain to exchange for a new liquid flow meter. 

 

The backing behind the glass tube has two scales printed on it. The left side, marked with “Silver ball”, 
is the scale to read the silver BB’s position. The right side, marked with “Black ball”, is the scale to read 
the black BB’s position. The unit of measurement of both scales is in mL/min, which is the same as 
cc/min. 

 

Figure 9:

 Black and silver ball scales. 

 

Figure 10:

 Units of both scales. 

 

When the black BB is above 11 cc/min on its scale, begin using the silver BB and its scale for readings 
until the black BB drops back below 11 cc/min. 

 

Monitoring the flow through the liquid flow meter can reveal much about the cable. 

Summary of Contents for NRI 603













Reviews: