background image

 

 

Emergency Procedures 

1.

 

In case of a brake failure, hold the steering wheel firmly, wait until the tractor has come to a complete stop 

and then shut down the engine. 

2.

 

If the steering malfunctions, brake immediately and shut down the engine. 

3.

 

If  fire  should  occur,  immediately  shut  down  the  engine  and  get  off  the  tractor.  If  a  fire  extinguisher             

is available, put out the flames at the source of the flame. If a fire extinguisher is not available, use sand or 

another non-flammable substance to fight the fire. 

4.

 

After  any  safety  incident,  immediately  dial  any  necessary  emergency  services  (hospital,  fire  department) 

according to the situation and administer first-aid as necessary.

 

 

WARNING: 

1.

 

Always operate the tractor in a safe and responsible manner to avoid injury and possible death. 

2.

 

Pay  special  attention  to  any  obstacles  that  may  impede  progress  or  cause  an  accident  before  starting  the 

tractor.  Also  check  for  obstacles  and  impediments  that  may  be  covered  by  the  tractor,  an  implement  or       

a trailer. 

3.

 

Never leave the driver’s seat to start and operate the tractor. Prior to the startup, make sure that various shift 

levers are in the neutral position, the throttle lever and the front drive control handle are disengaged, and 

the lifter operating handle is in neutral to prevent the sudden start up of accessories. 

4.

 

Do not start the engine by bridging-over the starter solenoid. If you do this, the tractor could lose control 

and cause a dangerous situation, which could lead to injury or death. 

5.

 

Make  sure  that  the  pedals  are  free  from  obstacles  and  able  to  move  unhindered  to  their  home  position. 

Never  keep  anything  on  the  floor  or  around  the  pedals  that  could  obstruct  pedal  travel.  An  extra  foot 

blanket  or  non-standard  floor  mats  should  not  be  used  as  they  can  hinder  pedal  movement  and  cause 

serious injury or damage.   

6.

 

Never get on or off the tractor while it is in motion.   

7.

 

Never climb under the tractor while the engine is running.   

8.

 

Always remove the keys, set all shift levels to neutral, and lock the auxiliary brake handle before exiting 

the cab to avoid accidental start up and to keep the tractor from moving unattended. 

9.

 

Keep  your  speed  under  control  at  all  times.  Brake  prior  to  turning  in  order  to  maintain  your  load  and   

avoid tipping.   

10.

 

When crossing or going under a bridge or going through a tunnel, pay full attention to the load height. 

11.

 

Use  the  lowest  gear  with  the  clutch  enabled  on  a  down  slope.  Never  put  the  tractor  in  neutral  and  coast 

downhill as this can cause instability. Never change gears on a down slope as this can cause instability and 

a possible rollover. 

12.

 

Avoid sudden turns at high speed or using unilateral braking to turn as this can result in instability.   

13.

 

When driving on roads, obey all local traffic indicators and laws.   

14.

 

Keep a safe distance between the tractor and any other vehicles that may be on the road. 

15.

 

Roadbeds along the ditch line tend to be more fragile. Pay special attention to the weight of your vehicle 

when riding on the road shoulder.   

16.

 

Never overload the tractor. Running the tractor over the specified limits can cause damage to the tractor and 

can result in injury.   

17.

 

When driving at night, make sure that you have proper lighting to avoid any collisions.   

18.

 

When  working  in  tall  grass  or  hay,  a  spark-extinguishing  device  must  be  affixed  to  the  exhaust  pipe  to 

avoid accidental fires.   

19.

 

Always slow down when working in wet or rainy conditions to avoid slippage and instability. 

Summary of Contents for NorTrac 40XT












































































































Reviews: