19 08099A-1
NOTE:
The unit returns to idle state if no mail button is pressed within 10 seconds.
B.
RECORDING A MEMO INTO THE MESSAGE CENTER
1.
Press and
hold
the MEMO button. The MESSAGE CENTER LED will turn on. The unit will
announce
“
Please record your
message after the beep.”
The Digital LED Display will show the elapsed time of the recording.
2.
While still
holding
the MEMO button, begin your recording. You can record up to a maximum recording time of two minutes.
3.
Release the MEMO button when you have finished recording your memo. The Excursion
®
39765 will announce
“
End of
Recording.”
The Digital LED Display will be advanced by one count for the Message Center.
PLAYING BACK OF MESSAGES / MEMOS
If any of the mailbox indicator LEDs are ON, it indicates that you have messages. The Digital LED Display normally shows only the
number of messages in Message Center. Press MAIL l or MAIL 2 button to see how many messages have been recorded in each
mailbox.
A.
PLAYING MESSAGES
•
Press the desired mailbox button (MAIL l, MAIL 2, or
MESSAGE CENTER / STOP). The Excursion
®
®
39765
will announce
“
Mailbox (number). You have (number) messages.”
The Digital LED Display shows
the total number of messages in the selected mailbox momentarily, (Figure 24)
then displays the number of message being played. The Excursion
®
39765 begins playing the first message to the end. It will
announce the message number before each message.
B.
PREVIOUS MESSAGES
•
Press the PREV button once during message playback to skip backward one message.
C.
REPEATING MESSAGE
•
Press the REPEAT button once during
message (Figure 25) playback.
D.
SKIPPING MESSAGES
•
Press the SKIP button during
message playback to skip to the next message.
E.
STOP MESSAGE PLAYBACK
•
Press the MESSAGE / STOP button to stop message playback.
ERASING MESSAGES
A.
SELECTIVE ERASING
1.
Press
the ERASE button during
message playback. The Digital LED Display will show “
ER”.
2.
The Excursion
®
39765 will announce
“
Message (number) erased.
”
and then start the next message.
(Figure 26)
NOTE:
Erased messages cannot be retrieved. There is a momentary delay after erasing messages to allow the Excursion
®
39765 to
reorganize and optimize its memory space.
B.
ERASING ALL MESSAGES IN THE MESSAGE CENTER
1.
Press and
hold
the ERASE button until a beep is heard. The Digital LED Display goes blank
(00),
and the Message Center
(primary mailbox) LED indicator will turn off.
2.
The Excursion
®
39765 will announce
“
Messages Erased. You have no messages
.
”
All messages are now erased in the message
center.
NOTE:
The
Excursion
®
39765 will announce
“
You have no messages.”
if there are no more messages.
C.
ERASING ALL MESSAGES IN MAILBOX 1 OR MAILBOX 2
1.
Press the ERASE button.
2.
The Excursion
®
39765 will beep and prompt
“
Enter Mailbox number.”
The unit will beep and mail 1 and mail 2 LED indicator will
flash.
3.
Press and
hold
the selected mailbox button until a beep tone is heard. The Excursion
®
39765 will announce
“
Messages Erased.
You have no messages
”
.
All messages are now erased in the selected mailbox.
MEMORY FULL DETECTION
The memory full condition occurs:
•
If 10 minutes of recording time is reached, or
•
If 59 messages (i.e. memo, OGM, ICM) have been recorded as indicated by the Digital LED Display shown as
“
FU
”
.
Erasing
messages will eliminate this condition.
NOTE:
If there is an incoming call, the unit will answer the 10
th
ring and announce
“
Memory full
”
.
You can erase any or all the
messages remotely after listening to them. Refer to the REMOTE OPERATION section for more details.
CALL SCREENING / AUTO DISCONNECT
You can listen to the caller leave their ICM and decide if you
want to answer the call.
A.
FROM THE HANDSET (Away From the Base Unit)
1.
When the
Excursion
®
39765 rings, press the REMOTE button on the handset. The Excursion
®
39765 will immediately answer the
call. You will hear your OGM followed by the caller's
message through the handset receiver.
SCREEN
