background image

26

INSTALLATION CHECKLIST

INSTALLER NAME:

CITY:

STATE:

INSTALLATION ADDRESS:

CITY:

STATE:

UNIT MODEL #

UNIT SERIAL #

Minimum clearances per 

Table 1, 

(page 4)

?

YES

NO

Is the unit properly installed and 

leveled?

YES

NO

Does condensate drain properly 

in both drain tubes?

YES

NO

Has the owner’s information been 

reviewed with the home-owner?

YES

NO

Has the literature package been 

left near the appliance?

YES

NO

ELECTRICAL SYSTEM

Electrical connections tight?

YES

NO

Line voltage polarity correct?

YES

NO

Supply Voltage: ____________________________

_______

(V)

Has the thermostat been calibrated?

YES

NO

Is the thermostat level?

YES

NO

Is the heat anticipator setting correct?

YES

NO

ATTENTION INSTALLERS:

It is your responsibility to know this product better than your customer. 
This includes being able to install the product according to strict 
safety guidelines and instructing the customer on how to operate 
and maintain the equipment for the life of the product. Safety should 
always be the deciding factor when installing this product and using 
common sense plays an important role as well. Pay attention to 
all safety warnings and any other special notes highlighted in the 
manual. Improper installation of the furnace or failure to follow safety 
warnings could result in serious injury, death, or property damage.

These instructions are primarily intended to assist qualified individuals 
experienced in the proper installation of this appliance. Some local 
codes require licensed installation/service personnel for this type 
of equipment. Please read all instructions carefully before starting 
the installation. Return these instructions to the customer’s package 
for future reference.

Summary of Contents for B64EM Series





























Reviews: