background image

38

Table 12.  Gas Flow Rate

Primary Gas Valve –

 The gas valve controls the

flow of gas to all of the burners. When the gas
valve is energized it automatically opens and
regulates the gas pressure in the manifold.

Secondary Gas Valve –

 The gas valve controls

the flow of gas to the high fire burners only.

Pressure Switch –

 The pressure switch veri-

fies that the inducer is drawing the combustion
gases through the heat exchanger.  It also
senses a blocked condensate drain condition.

Vent Pressure Switch –

 The vent pressure

switch reacts to blockage in the vent or combus-
tion air piping.

Supply Air Limit Switch –

 The supply air limit

switch prevents the air temperature leaving the
furnace from exceeding the maximum outlet air
temperature.

Vent Safety Switch –

 The vent safety switch

shuts the furnace down if the outlet flue gas
temperature increases above 160°F. This switch
protects the plastic flue system and the inducer
from over-temperature conditions.

Flame Roll-Out Switch –

 This switch provides

flame roll-out protection to the furnace and
combustion air inlet pipe.

MAINTENANCE

It is recommended that the furnace be checked
yearly.  At a minimum, this check should include
the following items.

!

 WARNING:

To avoid electric shock, personal injury,
or death, disconnect the electric power
before performing any maintenance.

!

 WARNING:

Holes in the vent pipe or heat exchanger
can cause products of combustion to
enter the home.  Replace the vent pipe
or heat exchanger if leaks are found.
Failure to prevent products of com-
bustion from being circulated into the
living space can create potentially haz-
ardous conditions including carbon
monoxide poisoning that could result
in personal injury or death.

TIME FOR

TIME FOR

ONE REVOLUTION

ONE REVOLUTION

(SECONDS)

1

5

10

(SECONDS)

24

150

750

1500

74

26

138

692

1385

76

28

129

643

1286

78

30

120

600

1200

80

32

113

563

1125

82

34

106

529

1059

84

36

100

500

1000

86

38

95

474

947

88

40

90

450

900

90

42

86

429

857

92

44

82

409

818

94

46

78

391

783

96

48

75

375

750

98

50

72

360

720

100

52

69

346

692

102

54

67

333

667

104

56

64

321

643

106

58

62

310

621

108

60

60

300

600

110

62

58

290

581

112

64

56

281

563

114

66

55

273

545

116

68

53

265

529

118

70

51

257

514

120

72

50

250

500

GAS FLOW RATE (CUBIC FEET PER HOUR)

CUBIC FEET PER REVOLUTION OF 

METER

1

5

10

49

243

486

47

237

474

46

231

462

45

225

450

44

220

439

43

214

429

42

209

419

41

205

409

40

200

400

39

196

391

38

191

383

38

188

375

37

184

367

36

180

360

35

176

353

35

173

346

34

170

340

33

167

333

33

164

327

32

161

321

32

158

316

31

155

310

31

153

305

30

150

300

CUBIC FEET PER REVOLUTION OF 

METER

Summary of Contents for TC060













































Reviews: