manualshive.com logo in svg

Nordyne TC060, Installation Instructions Manual

Share
Download
Nordyne TC060 Installation Instructions Manual Download Page 16

16

!

 CAUTION:

Do not supply combustion air from an
attic space that is equipped with power
ventilation or any other device that
may produce a negative pressure.

VENTING REQUIREMENTS

This section specifies installation requirements
for vent and "2-pipe" combustion air piping.  For
"one pipe"  installations, install vent piping per
this section and provide air for combustion and
ventilation per the previous section. The capac-
ity table provided in this section applies to the
total of vent and combustion air piping for either
type of installation.

5/8"

Inlet

Exhaust

Combustion

Offset with
Exhaust Pipe
for Adequate
Dimensional
Clearance

PVC or
ABS Pipe

See Vent Table 4

Straps or Other Suitable

Supports at Minimum of 5 ft. Intervals

Upward Pitch - 1/4" per Foot

Outlet Exhaust Vent

First Support Placed
as Close to Furnace
Connection as Possible

Exhaust Vent

Wall

Seal/Caulk
around Pipe
at Building

90˚ Elbow

12" Min.

Normal Snow Level

7"

Straight Neoprene Coupling
with 2 Hose Clamps*
(Optional - Not Shown)

5/8"

Inlet

Exhaust

Combustion Air

Inlet

Offset with Exhaust 
Pipe for Adequate
Dimensional
Clearance

PVC or
ABS Pipe

See Vent Table 4

Straps or Other Suitable

Supports at Minimum of 5 ft. Intervals

Upward Pitch - 1/4" per Foot

Outlet Exhaust Vent

First Support Placed

as Close to Furnace

Connection as Possible

Exhaust Vent

Wall

Seal/Caulk
around Pipe
at Building

90˚ Elbow

12" Min.

Normal Snow Level

Straight Neoprene
Coupling with
2 Hose Clamps*

Figure 16. Horizontal Venting

* These neoprene couplings are field-supplied and can be used if the installation requires breakable connections

in the piping. Note that a maximum of two couplings per pipe are allowed.

Upflow Furnaces

Downflow Furnaces

Summary of Contents for TC060













































Reviews:

No comments

Brands by name

Popular brands

Load more brands