Nordyne TC060 Installation Instructions Manual Download | Manualshive

Page: 42 / 44

background image

42

Furnace Fails to Operate

If the furnace does not operate check the
following:
1. Is the thermostat operating properly?

2. Are the blower compartment door(s) in

place?

3. Is the furnace disconnect closed?

4. Has the circuit breaker tripped or the con-

trol board fuse burned open?

5. Is the gas turned on?

6. Are any manual reset switches open?

7. Is the filter dirty or plugged?

8. Is the flame sensor coated? (Remove and

clean with emery cloth.)

If the furnace locks out after 5 attempts for
ignition, it will try again every hour if a call for heat
remains. If the inducer and circulating air blow-
ers are operating, and items 1 through 8 have
been checked, press the red reset button on the
vent safety switch. (See Figure 29.) If the
furnace operates after depressing the reset
button, contact a qualified serviceman to identify
and repair the problem.

If the furnace continues to not operate, depress
the red reset buttons on the flame rollout
switches. (See Figure 29.) If the furnace oper-
ates after depressing the reset buttons, contact
a qualified servicemen to identify and repair the
problem.

«
...
40
41
42
43
44
»

Summary of Contents for TC060













































Reviews:

No comments

Related manuals for TC060

Brand: Valley Comfort Systems Pages: 26

Brand: Unitary products group Pages: 4

Brand: Heat Controller Pages: 10

Brand: Regency Pages: 28

Brand: Johnson Controls Pages: 41

Brand: Fluke Pages: 90

Brand: Bryant Pages: 85

Brand: Blaze King Pages: 40

Brand: York Pages: 4

Brand: York Pages: 8

CARBOLITE GERO HST 12/200

Brand: VERDER Pages: 38

CARBOLITE GERO HTF 18/15

Brand: VERDER Pages: 62

CARBOLITE GERO HTF 18/8

Brand: VERDER Pages: 70

CARBOLITE GERO HTF 18/4

Brand: VERDER Pages: 68

CARBOLITE GERO HTF 18/27

Brand: VERDER Pages: 72

FINOSINT KOMPAKT

Brand: FINO Pages: 38

Brand: Rheem Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands