Nordmann Engineering Omega 12 Operation Manual Download Page 89

Page: 89 / 104

Warning

Fault

Message

Possible causes

Remedy

–––

E170

Hum. Sensor out of Range

The measured humidity in the cabin is outside the permissible

range.

Note: The operation of the Condair Delta SPA Control Box or

Nordmann Omega is stopped. After eliminating the fault, the

Condair Delta SPA Control Box or the Nordmann Omega must be

switched off and on again (depending on which device the fault has

occurred).

Wrong humidity sensor con-

nected.

Check that the correct humidity

sensor is connected.

Humidity sensor not connected

or not correctly connected.

Check/correctly connect the

wiring of the humidity sensor.

Incorrect configuration of the

humidity sensor in the control

software.

Check/correctly set the humidity

sensor settings in the control

software.

Humidity sensor defective.

Replace humidity sensor.

–––

E171

Hum. Sensor

Instable

Measurement of cabin humidity unstable.

Note: The operation of the Condair Delta SPA Control Box or

Nordmann Omega is stopped. After eliminating the fault, the

Condair Delta SPA Control Box or the Nordmann Omega must be

switched off and on again (depending on which device the fault has

occurred).

Unstable humidity measurement

due to manipulation of the humi-

dity sensor in the cabin.

Check humidity sensor in the

cabin.

–––

E172

Bench Sensor out of Range

The measured bench temperature in the cabin is outside the per-

missible range.

Note: The operation of the Condair Delta SPA Control Box or

Nordmann Omega is stopped. After eliminating the fault, the

Condair Delta SPA Control Box or the Nordmann Omega must be

switched off and on again (depending on which device the fault has

occurred).

Wrong temperature sensor

connected.

Check if the correct temperature

sensor is connected.

Temperature sensor not or not

correctly connected.

Check/correctly connect the wi-

ring of the temperature sensor.

Incorrect configuration of the

temperature sensor in the con-

trol software.

Check/correctly set temperature

sensor settings in the control

software

Temperature sensor defective.

Replace temperature sensor.

–––

E173

Wall Sensor out of Range

The measured wall temperature in the cabin is outside the permis-

sible range.

Note: The operation of the Condair Delta SPA Control Box or

Nordmann Omega is stopped. After eliminating the fault, the

Condair Delta SPA Control Box or the Nordmann Omega must be

switched off and on again (depending on which device the fault has

occurred).

Wrong temperature sensor

connected.

Check if the correct temperature

sensor is connected.

Temperature sensor not or not

correctly connected.

Check/correctly connect the wi-

ring of the temperature sensor.

Incorrect configuration of the

temperature sensor in the con-

trol software.

Check/correctly set temperature

sensor settings in the control

software

Temperature sensor defective.

Replace temperature sensor.

Summary of Contents for Omega 12









































































































Search results

Summary of Contents for Omega 12

Reviews:

Related manuals for Omega 12

Brands by name

Popular brands

Nordmann Engineering Omega 12, Operation Manual

Search results

Summary of Contents for Omega 12

Reviews:

Related manuals for Omega 12

Brands by name

Popular brands