57
Outputs
Determining of the settings for controlling the additional relays 8 and 9.
– Relay 8 Mode: Determining whether the additional relay 8 is activated automatically de-
pendent on the corresponding states of relay 8 ("Auto Status") or whether the additional
relay 8 should be used for the control of the bench heating ("bench heater") or the wall
heating ("wall heater") or whether the additional relay 8 is deactivated ("Off").
– Relay 8 On States: Determining in which operating states relay 8 should be activated
automatically. Several operating states can be selected ("Off": When the unit is ready,
"Keep Warm": During the keep warm phase, "Warm Up": During the Warm-up phase:,
"Bathing": During the bathing operation, "Drying": During the drying phase, "Stop": If the
bathing operation was stopped by a fault).
Note
: With the Rasul application additional operating states can be selected ("Pre-Treatment":
During the Warm-up phase: for the treatment, "Treatment": During the treatment phase,
"Shower": During the showering phase).
– Relay 9 Mode: Determining whether the additional relay 9 is activated automatically de-
pendent on the corresponding states of relay 9 ("Auto Status") or whether the additional
relay 9 should be used for the control of the bench heating ("bench heater") or the wall
heating ("wall heater") or whether the additional relay 9 is deactivated ("Off").
– Relay 9 On States: Determining in which operating states relay 9 should be activated
automatically. Several operating states can be selected ("Off": When the unit is ready,
"Keep Warm": During the keep warm phase, "Warm Up": During the Warm-up phase:,
"Bathing": During the bathing operation, "Drying": During the drying phase, "Stop": If the
bathing operation was stopped by a fault).
Note
: With the Rasul application additional operating states can be selected ("Pre-Treatment":
During the Warm-up phase: for the treatment, "Treatment": During the treatment phase,
"Shower": During the showering phase).
Sauna Heater
Note
: This menu only appears for Fin sauna application and Bio sauna application if the heating type of the sauna heater is
set to "Internal" or "External Analog".
Heat Kind
Determining of the settings for controlling the sauna heater.
–
None: The control of the sauna heater takes place externally, not via about the SPA Control.
– Internal: The power supply as well as the control of the sauna heater are provided by the
SPA Control.
– External Analog: An externally powered sauna heater is controlled via an analog signal
from the SPA Control.
Heat settings
Display of the currently calculated demand to the sauna heater in % .
Heater
Determining of the settings for the internal heating control of the sauna heater.
– Heat Power: Determining of the heating power of the connected sauna heater (3 kW, 6
kW or 9 kW).
– Heat Output: Indicates the current demand of the sauna heater in %.
Omega Control Board
Note
: This menu only appears for applications using a Nordmann Omega with Omega Control.
System Mode
Determining in which system mode the
Omega Control Board
should run.
– Steam Generator: Setting for the operation of the Nordmann Omega with Omega Control
as a pure steam generator for steam shower application. The steam production is controlled
by a demand signal from an external controller.
CAUTION!
With this setting bathing time is not monitored. Make sure that the external
control monitors the maximum allowed bathing time!
– Wellness: Setting for single cabin application. The control takes place in accordance with
the application via the device-specific control of the Condair Delta SPA Control Box or the
Nordmann Omega.
– Wellness Dual: Setting for dual cabin application for small cabins. The control of the two
cabins takes place in accordance with the application via the device-specific controls of
the Condair Delta SPA Control Box or the Nordmann Omega with SPA Control.
Generator Kind
Determining of the type of steam generation used for steam shower, steam Bath, Rasul or Bio
sauna application
– None: There is no steam generator used.
– Internal Omega: The steam is produced by a Nordmann Omega with Omega Control.
Signaling
Activation ("On") or deactivation ("Off") of the beeper for fault/warning signalisation.
