Nokia ESB26 User Manual Download | Manualshive

Page: 315 / 421

background image

MN700004 Rev 01

304

26. Remote Monitoring

Introduction

Remote Monitoring

(RMON)

is a standard monitoring specification that enables various

network monitors and console systems to exchange network-monitoring data. RMON
provides network administrators with more freedom in selecting network-monitoring probes
and consoles with features that meet their particular networking needs. This section provides a
brief overview of the RMON specification, focusing on RMON groups.

The RMON specification defines a set of statistics and functions that can be exchanged
between RMON-compliant console managers and network probes. As such, RMON provides
network administrators with comprehensive network-fault diagnosis, planning, and
performance-tuning information.

Feature Overview

Packets Definitions

Good Packets

Good packets are error-free packets that have a valid frame length. For example, on Ethernet,
good packets are error-free packets that are between 64 and 1518 octets long. They follow the
form defined in IEEE 802.3.

Bad Packets

Bad packets are packets that have proper framing and are therefore recognized as packets, but
contain errors within the packet or have an invalid length. For example, on Ethernet, bad
packets have a valid preamble and Start of Frame Delimiter

(

SFD), but have a bad Cyclic

Redundancy Check (CRC) or are either shorter than 64 octets or longer than 1518 octets.

RMON Groups

The ESB26 switch supports the following four RMON groups:

•

Statistics

•

History

•

Alarms

•

Events

«
...
313
314
315
316
317
...
»

Summary of Contents for ESB26






































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ESB26

Brand: F-SECURE Pages: 19

Brand: SAF Pages: 30

Brand: Allnet Pages: 12

Brand: Telebyte Pages: 19

LinkSmart KW6515

Brand: Kasda Pages: 31

Brand: 3Com Pages: 50

Brand: National Instruments Pages: 8

Brand: Infoblox Pages: 13

Brand: Avaya Pages: 73

Brand: Airlinkplus Pages: 20

Brand: Raven Pages: 33

Brand: Aviosys Pages: 77

Brand: Maestro Wireless Solution Pages: 22

JetNet 5720G-8P Series

Brand: Korenix Pages: 52

Brand: Proxim Pages: 65

Brand: Thecus Pages: 90

Brand: ASTRO Pages: 12

Brand: CHINT Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands