background image

SERVICE - MAINTENANCE

Especially for the replacement of the anode bar follow these steps:

1. 

Shut down the electrical supply and open the electri-

cal components’ cover.

2. 

Check the cable connection between the thermostat 

and the heating element.

3. 

Check the temperature at which the thermostat is set, 

so that it is not lower than that needed for consump-

tion.

4. 

Check the heating element.

5. 

Check the central electrical connection.

6. 

Switch on the electrical current and measure the volt-

age at the heating element’s terminals. 

7. 

Check  the  thermostat’s  thermoelectric  fuse,  which 

must be pressed in. If it is not, rotate the thermostat’s 

regulator until the button of the thermoelectric fuse 

appears. Press this. Once it has been reset, the ther-

mostat can operate once again.

THE SOLAR WATER STORAGE TANK DOES NOT SUPPLY HOT WATER WHEN USING

THE ELECTRICAL HEATING ELEMENT

The following tasks must be carried out only by a qualified electrician.

1. 

Shut down the electrical supply.

2. 

Empty the water from the water storage tank.

3. 

Remove the electrical component’s cover.

4. 

Disconnect the three electrical wires.

5. 

Remove the electrical heating element by removing 

the M8 screws.

6. 

Remove the old magnesium bar from the heating el-

ement’s flange.

7. 

Screw in the new magnesium.

8. 

Replace the heating element with the rubber seal.

9. 

Open the water supply and a hot water tap until the 

water storage tank fills up.

10. 

Check for water leaks. 

11. 

Reconnect the electrical components at their desig-

nated positions. 

12. 

Check that the thermostat is securely clipped to the 

heating element.

13. 

Replace the electrical component’s cover. 

14. 

Reconnect the electrical supply.

1. 

Flange

2. 

Safety valve

3. 

Heating element - thermostat 

4. 

Connection fittings

5. 

Piping

6. 

Insulation - seals 

7. 

Transparent cover (solar glass)

8. 

Supporting system

9. 

Replacement of anode and check-

ing the closed loop’s liquid. 

It  is  recommended  that  the  water  storage  tank 

is cleaned of mineral deposits and sludge every 

five years.

Your solar water heater should be serviced every two years by an authorized representative or a company techni-

cian. These periodic checks are necessary for the solar water heater’s warranty to apply. The inspection concerns 

the whole system and more specifically:

For solar water storage tanks with a heating coil a periodic check by a qualified technician is recommended.

Solar water heaters

35

34

Solar water heaters - AELIOS

Solar water heaters - AELIOS

Summary of Contents for aelios









































Reviews: