INSTRUCTIONS FOR USE
33015122(1)2006-02
25
ENGINE OIL LEVEL CHECK
1.
Empty the hopper (12, Fig. G); if it contains a small
quantity of waste, it is not necessary to dump it.
2.
Drive the machine on a solid and level ground, then
engage the parking brake (7, Fig. E).
3.
Lift the hopper (12, Fig. G), according to the procedure
shown in the relevant paragraph.
4.
Turn off the engine, by turning the ignition key (17, Fig.
D) counterclockwise, to the end of stroke, then remove
it.
5.
Open the left panel door (4, Fig. G) by releasing the
fasteners (5) with the supplied key.
6.
Remove the lifted hopper locking pins (9, Fig. F) from the
housings (10), and place them into the holes (11).
7.
Empty the dust control system water tanks (17 and 21,
Fig. F) according to the instructions shown in the
relevant paragraph.
8.
Remove the screw (23, Fig. F) and open the left tank
(21) outwards.
9.
Check the oil level as described in the diesel engine
Manual.
10. If necessary, add oil as described in the diesel engine
Manual.
11. Perform steps 3, 4, 5, 6 and 8 in the reverse order.
12. If necessary, fill the dust control system water tanks
according to the procedure shown in Before Start-Up
paragraph.
ENGINE OIL CHANGE
1.
Empty the hopper (12, Fig. G); if it contains a small
quantity of waste, it is not necessary to dump it.
2.
Drive the machine on a solid and level ground, then
engage the parking brake (7, Fig. E).
3.
Lift the hopper (12, Fig. G), according to the procedure
shown in the relevant paragraph.
4.
Turn off the engine, by turning the ignition key (17, Fig.
D) counterclockwise, to the end of stroke, then remove
it.
5.
Open the right and left panel doors (16 and 4, Fig. G) by
releasing the fasteners (17 and 5) with the supplied key.
6.
Remove the lifted hopper locking pins (9, Fig. F) from the
housings (10), and place them into the holes (11).
7.
Empty the dust control system water tanks (17 and 21,
Fig. F) according to the instructions shown in the
relevant paragraph.
8.
Remove the screw (19, Fig. F) and open the right tank
(17) outwards.
9.
Change the oil as described in the diesel engine Manual.
10. Perform steps 3, 4, 5, 6 and 8 in the reverse order.
11. If necessary, fill the dust control system water tanks
according to the procedure shown in Before Start-Up
paragraph.
ENGINE OIL FILTER REPLACEMENT
1.
Empty the hopper (12, Fig. G); if it contains a small
quantity of waste, it is not necessary to dump it.
2.
Drive the machine on a solid and level ground, then
engage the parking brake (7, Fig. E).
3.
Lift the hopper (12, Fig. G), according to the procedure
shown in the relevant paragraph.
4.
Turn off the engine, by turning the ignition key (17, Fig.
D) counterclockwise, to the end of stroke, then remove
it.
5.
Open the left panel door (4, Fig. G) by releasing the
fasteners (5) with the supplied key.
6.
Remove the lifted hopper locking pins (9, Fig. F) from the
housings (10), and place them into the holes (11).
7.
Empty the dust control system water tanks (17 and 21,
Fig. F) according to the instructions shown in the
relevant paragraph.
8.
Remove the screw (19, Fig. F) and open the right tank
(17) outwards.
9.
Replace the oil filter as described in the diesel engine
Manual.
10. Perform steps 3, 4, 5, 6 and 8 in the reverse order.
11. If necessary, fill the dust control system water tanks
according to the procedure shown in Before Start-Up
paragraph.
WARNING!
Open the tanks (17 and 21, Fig. F) outwards,
only if they are empty: each tank contains
253.5 lb (115 kg) of water approximately.
WARNING!
Open the tanks (17 and 21, Fig. F) outwards,
only if they are empty: each tank contains
253.5 lb (115 kg) of water approximately.
NOTE
This procedure must be performed when the
engine oil has been drained.
WARNING!
Open the tanks (17 and 21, Fig. F) outwards,
only if they are empty: each tank contains
253.5 lb (115 kg) of water approximately.
https://harrissupplyind.com - To Order Parts Call 608-268-8080