Nilfisk-Advance RS 2200, User Manual

Page: 130 / 224

ENGLISH USER MANUAL
8 33019476(3)2010-02 A RS 2200
Electrical panel functions:
AIA: Accelerator electronic board –
F3: Fuse box (see Electrical Fuses paragraph) –
F4: Fuse box (see Electrical Fuses paragraph) –
F6: Fuse box (see Electrical Fuses paragraph) –
K1.1: Working light power supply relay –
K1.2: Rear working light relay –
K1.3: Suction inlet working light relay –
K1.4: Front working light relay –
K1.5: Hydraulic enabling relay –
K1.6: Gear selector relay –
K1.7: Windscreen wiper relay –
K2: Cab accessory power supply relay –
K3: Fuel heater relay –
K4: Hydraulic system enabling relay –
K41: Windscreen wiper intermittence –
P7: Quick coupler control electronic board –
P8: Function-accessory electronic board –
P10: Engine accessory electronic board –
P11: Drive system electronic board –
X10: Cab main power supply relay –
Combination switch functions:
High beam on by pressing the lever (1, Fig. P) downward, –
or by turning the switch (17, Fig. E) to the second position.
High beam temporarily on by pressing and holding the
–
lever (1, Fig. P) upward.
Right turn signal on by bringing the lever (1, Fig. P)
–
forward.
Left turn signal on by bringing the lever (1, Fig. P)
–
backward.
Horn sounding by pressing the push-button (6, Fig. P) on
–
the top of the lever (1).
Windscreen washer on by pressing the push-button (2,
–
Fig. P) on the top of the lever (1).
Windscreen wiper intermittence with mark (3, Fig. P) at the
–
symbol “I” (4).
Windscreen wiper on with mark (3, Fig. P) at the symbol
–
“II” (5).
Display functions:
When the key is turned to ON 1.
When the ignition key (6, Fig. D) is turned to the fi rst
position, the display (32, Fig. E) shows for a few seconds
the
fi rst page (23, Fig. H) with numbers or symbols that
indicate the machine condition. The parameters that can
be checked are shown below.
Scheduled maintenance intervals • . MA0 (15, Fig. H)
indicates the scheduled maintenance at 150 hours,
while MA1 (16) indicates the scheduled maintenance
at 500 hours. If one of the intervals is nearly expired or
expired (negative number), maintenance procedures
must be performed as shown in the relevant chapter.
NOTE
When one of the maintenance intervals has
expired, one of the symbols (15 or 16, Fig.
H)
fl ashes for a few seconds at machine
start-up.
Enabled hydraulic system • (21, Fig. H).
WARNING!
If the symbol is not shown, but
the key appears on the display, it
means that the maintenance interval
has expired. Proceed as shown in the
relevant chapter.
Number of working hours • (14, Fig. H).
Odometer • (18, Fig. H).
Alarm counter • (17, Fig. H). It counts the number of
alarms occurred after the last reset of the control unit.
If the number is different from zero, contact a Nil
fi sk
Service Center to reset the system.
Software overhaul • (19, Fig. H).
Road sweeper identi fi cation number • (20, Fig. H).
The number “004” identi fi es the RS 2200 model, with
VM R754 EU4 engine.
Fasten the seat belts • . The fl ashing symbols (22, Fig.
H) warns that the seat belts must be fastened.
Transport mode visualisation 2.
When the key is turned to ON, the display (32, Fig. E)
automatically shows the transport mode visualisation (13,
Fig. H) thus replacing the screen (23). The screen (13, Fig.
H) remains even after the engine has been turned on. This
screen shows the following parameters.
Machine speed • : 3-digit number (1, Fig. H) with the
following symbol
Km/h
(2).
WARNING!
The speedometer sensor cannot be
checked for ef
fi ciency, so the system
detects that the machine is running at 5
km/h even if the sensor is disconnected
or shorted, so the related safety systems
are disabled.
Fuel level • : the fuel level is shown by the horizontal
bar indicator (3, Fig. H). The last bars indicate the
reserve, they
fl ash when the level is low. The fuel level
instantaneous value in % (5, Fig. H) is shown too.
CAUTION!
If the level sensor is faulty, the display
shows warning messages (15 or 16, Fig.
I) according to the type of fault (for the
alarm coding see the Alarm Description
paragraph). To repair the circuit and
replace the level sensor, contact a Nil
fi sk
Service Center.
The symbol (4, Fig. H) indicates that the fuel level
indicator is activated.