USER MANUAL
909 6754 000(2)2006-10 A
5
–
Regularly check the power supply cable for damages, cracks, cuts, etc. If the power supply cable is damaged, replace it
immediately.
–
To avoid any risk, if the power supply cable is damaged, contact the Nilfisk-Advance Service Center or a qualified
technician.
–
Do not pull or carry the machine by the power supply cable and never use the power supply cable as a handle. Do not
close a door on the power supply cable, or pull the power supply cable around sharp edges or corners. Do not run the
machine on the power supply cable.
Keep the power supply cable away from heated surfaces.
–
To reduce the risk of fire, electric shock, or injury, do not leave the machine unattended when it is plugged in. Disconnect
the machine from the electrical mains when not in use and before performing maintenance procedures.
–
To avoid electric shock, do not expose the machine to rain or other bad weather conditions. Store the machine indoors,
in a dry place.
–
Do not allow to be used as a toy. Close attention is necessary when used near children.
–
Use only as shown in this Manual. Only Nilfisk-Advance recommended accessories must be used.
–
Take all necessary precautions to prevent hair, jewels and loose clothes from being caught by the machine moving parts.
–
Do not leave the machine unattended without being sure that it cannot move independently.
–
Do not use the machine on slopes with a gradient exceeding the specifications.
–
Do not use the machine in particularly dusty areas.
–
While using this machine, take care not to cause damage to people or objects.
–
Do not bump into shelves or scaffoldings, especially where there is a risk of falling objects.
–
Do not put any can containing fluids on the machine.
–
The machine working temperature must be between 0°C and +40°C.
–
The machine storage temperature must be between 0°C and +40°C.
–
The humidity must be between 30% and 95%.
–
Do not use the machine as a means of transport.
–
Do not use the machine on slopes with a gradient exceeding the specifications.
–
Do not allow the brush/pad to operate while the machine is stationary to avoid damaging the floor.
–
In case of fire, use a powder fire extinguisher, not a water one.
–
Do not tamper with the machine safety guards and follow the ordinary maintenance instructions scrupulously.
–
Do not leave any object penetrate in the openings. Do not use the machine if the openings are clogged. Always keep the
openings free from dust, hairs and any other foreign material which could reduce the air flow.
–
Do not remove or modify the plates affixed to the machine.
–
If the machine is used according to the instructions, the vibrations are not dangerous. The machine vibration level is less
than 2.5 m/s
2
(98/37/EEC-EN 1033/1995).
–
This machine cannot be used on roads or public streets.
–
Pay attention during machine transportation when temperature is below freezing point. The water in the recovery tank or
in the hoses could freeze and seriously damage the machine.
–
Use brushes and pads supplied with the machine and those specified in the User Manual. Using other brushes or pads
could reduce safety.
–
In case of machine malfunctions, ensure that these are not due to lack of maintenance. Otherwise, request assistance
from the authorised personnel or from an authorised Service Center.
–
If the machine
•
does not work properly
•
is damaged
•
has water or foam leaks
•
has been left outdoors exposed to bad weather conditions
•
is wet or has been dropped into water
turn it off immediately and contact the Nilfisk-Advance Service Center or a qualified technician.
–
If parts must be replaced, require ORIGINAL spare parts from a Dealer or Authorised Retailer.
–
To ensure machine proper and safe operation, the scheduled maintenance shown in the relevant chapter of this Manual,
must be performed by the authorised personnel or by an authorised Service Centre.
–
Carefully read all the instructions before carrying out any maintenance/repair procedure.
–
Do not wash the machine with direct or pressurised water jets, or with corrosive substances.
–
The machine must be disposed of properly, because of the presence of toxic-harmful materials (batteries, electronic
components, etc.), which are subject to standards that require disposal in special centres (see the Scrapping chapter).
