Nilfisk-Advance 56397010 Service Manual Download Page 13 | Manualshive

Page: 13 / 55

background image

12 - FORM NO. 56043056 / ConvertaMAX™ 20/26 / BA 550/650

Brush Remove Switch (15) – To remove the brush(es) from the machine, have the machine stationary and the Brush Deck (24) in
the “RAISED” position. Press the switch to the “REMOVE” position and release. The switch will snap to the OFF position, and the
brush(es) will drop to the floor.
Solution Flow Control Knob (16) – Turn this dial to the right to increase solution flow to the floor. Turn to the left, to decrease the
amount of solution flow to the floor. When the Drive Paddle (5) is released from either forward or reverse travel, the solution flow will
stop automatically, and resume when the drive is engaged.
Speed Limit Control Knob (17) – The Speed Limit Control Knob is used to adjust the maximum speed in both forward and reverse.
Master Key Switch (18) – The master power switch.
Auxiliary Circuit Breaker (19) – Provides overload protection. If it trips, it will pop out. To reset, wait one minute and press the button
back in. If any breaker trips repeatedly, have the machine serviced.
Vacuum Motor Circuit Breaker (20) – Provides overload protection to machine’s vacuum motor. If it trips, it will pop out. To reset,
wait one minute and press the button back in. If any breaker trips repeatedly, have the machine serviced.
Brush Motor Circuit Breaker (21) – Provides overload protection to machine’s brush motor(s). If it trips, it will pop out. To reset,
wait one minute and press the button back in. If any breaker trips repeatedly, have the machine serviced.
Wheel Drive Circuit Breaker (22) – Provides overload protection to machine’s wheel drive motor. If it trips, it will pop out. To reset,
wait one minute and press the button back in. If any breaker trips repeatedly, have the machine serviced.
Scrub Pressure Lever (23) – Two position lever provides two different scrubbing pressures.
TOP POSITION: – In this position the full weight of the scrub deck rests on the floor.
BOTTOM POSITION: – In this position the scrub pressure is approximately 30 pounds less.
Brush Deck (24) – Contains brush drive motor(s) and brush(es).
Operator Control Handle (25) – Operator holds onto this to control the machine.

KNOW YOUR MACHINE

revised 9/01

«
...
11
12
13
14
15
...
»

Summary of Contents for 56397010
























































Reviews:

No comments

Related manuals for 56397010

Professional Series

Brand: Janome Pages: 60

Brand: JUKI Pages: 2

Memory Craft 9450QCP

Brand: Janome Pages: 124

Brand: Lindhaus Pages: 25

Brand: Consew Pages: 38

Brand: Reliable Pages: 1

PhoneMate TC-520

Brand: Casio Pages: 40

1500 Contractors

Brand: MasterCraft Pages: 8

Brand: Siruba Pages: 28

Brand: Carina Pages: 30

Brand: Ricoh Pages: 256

Brand: Alto Pages: 51

Brand: Janome Pages: 45

AMS-210EN-HL1306

Brand: JUKI Pages: 12

Brand: Baby Lock Pages: 28

Brand: JUKI Pages: 124

Brand: JUKI Pages: 24

Brand: JUKI Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands