Nilfisk-Advance 56397010 Service Manual Download Page 3 | Manualshive

Page: 3 / 55

background image

2 - FORM NO. 56043056 / ConvertaMAX™ 20/26 / BA 550/650

INTRODUCTION

This manual will help you get the most from your ConvertaMAX™ 20/26 / BA 550/650. Read it thoroughly before servicing the machine.
Note: Bold numbers in parentheses indicate an item illustrated on pages 9-10.
This product is intended for commercial use only.

PARTS AND SERVICE

Repairs, when required, should be performed by your Authorized Nilfisk-Advance Service Center, who employs factory trained service personnel,
and maintains an inventory of Nilfisk-Advance original replacement parts and accessories.

Call the NILFISK-ADVANCE DEALER named below for repair parts or service. Please specify the Model and Serial Number when discussing
your machine.

(Dealer, affix service sticker here.)

NAME PLATE

The Model Number and Serial Number of your machine are shown on the Nameplate on the machine. This information is needed when ordering
repair parts for the machine. Use the space below to note the Model Number and Serial Number of your machine for future reference.

MODEL NUMBER

SERIAL NUMBER

TRANSPORTING THE MACHINE

CAUTION!

Before transporting the machine on an open truck or trailer, make sure that . . .

•

The machine is tied down securely - see tie-down locations (26).

•

All access doors and covers are secured (tape and strap as needed).

TOWING

CAUTION!

If the machine must be towed or pushed, make sure the Key Switch (Main Power) (18) is in the OFF position, disconnect wheel drive
motor wiring harness and do not move the machine faster than a normal walking pace (2-3 mph, 3-5kph) and for short distances only.

OTHER MANUALS AVAILABLE FOR YOUR MACHINE

The following manuals are available from the Nilfisk-Advance Literature Service Department (order according to model name, model number and machine’s serial
number):

•

A Parts List and Operation Manual are available for each machine.

•

The three Operation Manuals available for the BA 550/650 are multi-language: (Danish, Norwegian, Swedish, Finnish), (English, German, French,
Netherlands) or (Spanish, Portuguese, Italian, Greek)

GENERAL INFORMATION

revised 7/02

«
1
2
3
4
5
...
»

Summary of Contents for 56397010
























































Reviews:

No comments

Related manuals for 56397010

Brand: Panasonic Pages: 2

Brand: Baroness Pages: 163

Brand: MyBinding Pages: 3

Brand: HazeBase Pages: 9

Brand: Cleanfix Pages: 16

Brand: Chikon Pages: 17

Brand: Janome Pages: 61

Truvox International Orbis Compact

Brand: Tacony Pages: 14

Brand: Pfaff Pages: 50

Brand: Bosch Pages: 17

Brand: Bosch Pages: 56

Brand: Bosch Pages: 52

Brand: Bosch Pages: 40

Brand: Bosch Pages: 48

Brand: Brother Pages: 42

Brand: Crane Pages: 24

Brand: Zanussi Pages: 20

Brand: Zanussi Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands