Nilfisk-Advance 56397010 Service Manual Download Page 32 | Manualshive

Page: 32 / 55

background image

FORM NO. 56043056 ConvertaMAX™ 20/26 / BA 550/650 - 31

RECOVERY SYSTEM

Electrical Diagram

*For complete description of all callouts see Electrical System

Wiring Diagram

.

VACUUM / RECOVERY SYSTEM SERVICE MAINTENANCE CHECKLIST

Whenever there is a vacuum problem, it’s best to check over the entire system. Use the checklist below as a guide, to thoroughly check the vacuum
system.

Clean built-up dirt from the inside of the squeegee tool.

Replace the squeegee blades if they are nicked or torn.

Inspect the hose between the squeegee tool and the recovery tank, rinse any built-up dirt from the hose. Replace the hose if it is kinked
or damaged.

Inspect and make sure the gasket on the recovery tank cover is sealing and not damaged.

Inspect and clean the vacuum motor float cage.

Make sure that the recovery tank drain valve seals airtight.

TROUBLESHOOTING GUIDE

If water flows around the ends of the squeegee tool, instead of being pulled into the tool, the vacuum system is not working properly. When a vacuum
system performs poorly, it is usually because of one of the following problems:

Vacuum Leak(s) – Air flowing into the vacuum system past a bad gasket or leaky hose, damaged tank, or a leaky drain valve. A vacuum leak
below the water line will create turbulence in the recovery tank, causing water to enter the vacuum motor.

Restriction(s) – Anything that blocks the flow of air through the system. Restrictions may also be caused by built-up debris in the squeegee tool,
vacuum hoses, float cage or wherever the airflow is forced to make a sharp turn.

Both leaks and restrictions decrease the quantity of air flowing through the squeegee tool. The air that does go through the squeegee tool moves
slower, so it has less pick-up power.

FIGURE 2

F4

+24V

-24V

RED/GRN

RED

BLK

M

M1

BLU

K2

D1

K2

BLK

RED/WHT

S4

VIO

RED

S5

F1

S1

revised 9/01

«
...
30
31
32
33
34
...
»

Summary of Contents for 56397010
























































Reviews:

No comments

Related manuals for 56397010

Brand: Bartell Pages: 30

Brand: Oki Pages: 16

Brand: Oki Pages: 28

Brand: Clarke Technology Pages: 54

Brand: Singer Pages: 100

KM 85/50 W Classic

Brand: Kärcher Pages: 18

BX2 Fastracts Extractor

Brand: IPC Eagle Pages: 8

Brand: Thomas Pages: 24

Brand: Singer Pages: 13

Brand: IMER Pages: 11

Brand: Unicorn Pages: 28

Brand: DS Produkte Pages: 52

Brand: JUKI Pages: 140

Brand: Hitachi Pages: 48

Brand: SunStar Pages: 21

Brand: SunStar Pages: 37

Brand: SunStar Pages: 50

Brand: 1byone Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands