FORM NO. 56043124 - Condor XL
™
-
41
ADJUSTMENTS/REPAIRS
SIDE BROOM LIFT ACTUATOR MOTOR ADJUSTMENT
1
See Figure 7. This shows the jumper wiring needed to connect the machine battery to the three-wire connector on the actuator.
Note:
Reference the bill of materials for building the two jumper wires.
Important Service Note:
The power cord adapter (p/n 56407502)
normally used on all other two-wire actuator motors should not be used.
2
See Figures 7-A and 7-B. The wiring diagram illustrates the correct battery polarity (+ and -) power inputs to operate the actuator motor for both
extending and retracting the drive nut.
3
See Figure 7-A. Connect the jumper wiring as shown to run the actuator motor in the retracted (IN) mode.
4
Hold the drive nut tube (AE) and press the switch to run the drive nut toward the motor housing (it’s IN limit).
5
Measure the position of the drive nut on the actuator shaft, then compare it to the retracted dimension speci
fi
cation shown in Figure 7. Manually
turn the steel drive nut tube to match the IN position shown.
6
See Figure 7-B. Connect the jumper wiring to run the actuator motor in the extended (OUT) mode.
7
Hold the drive nut tube (AE) and press the switch to run the drive motor to the out position waiting for the motor to stop (reaching its Out limit).
8
Measure the position of the drive nut on the actuator shaft and compare the measurement with the OUT position shown in Figure 7.
9
If the measurement doesn’t match the dimension shown, it will be necessary to remove the large rubber Adjuster Cover (AF).
Note:
Use a 1/2”
(13mm) socket to turn the outside hex adjuster. Each click of the top adjuster (cam) will change the nut travel 1/16” (1.6mm). To extend the
travel of the drive nut, turn the adjuster clockwise. To retract the travel of the nut, turn the adjuster counterclockwise.
10
After each adjustment, hold the drive nut tube, run the actuator IN and OUT and check both dimensions.
Note:
When checking the directional
travel dimensions remember to change the connections (battery polarity) of the jumper wires.
11
Check that the drive nut limits are set correctly, then reinstall the Adjuster Cover (AF).
Service Tip:
Leave the correctly-adjusted actuator motor in the out (extended) position when you reinstall the motor.
FIGURE 7
6-7/8"
(175mm)
B
9-9/16"
(243mm)
A
IN
OUT
WHT
BLK
RED
Retract (IN)
Extend (OUT)
WHT
BLK
RED
RED
BLK
BLK
RED
BLK
RED
6-A
6-B
D
C
Jumper Wire Assembly
Bill of Material
Item Qty Description
1
Wire 16 gauge (red) 60" length
1
Wire 16 gauge (black) 60" length
A
2
Medium size insulated alligator clips (60 series)
B
2
Small size insulated alligator clips (30 series)
C
1
Normally Open snap switch part # 56385615
D
2
.250 (1/4) insulated female connectors
part # 56244138
RED
D
A
B
C
D
AE
AF
12 volt
battery
Summary of Contents for 56110000
