![background image](http://html.mh-extra.com/html/niko/410-000-series/410-000-series_quick-start-manual_1689717008.webp)
EN nv
Niko
sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: [email protected] — www.niko.eu
PM410-00xx0R17095
410-00xx0
8
3.4.2. Reset to factory settings
With this option, you return the smart switch to the factory settings. This means that all controls are deleted
from the memory and the feedback LED functions as a confirmation LED again.
Return to the factory settings as follows:
• Ensure that the switched lamps of the smart switch are not switched on.
• hold down (> 1.6 s.) the programming button (Prog.) of the smart switch.
The LED (Prog.) begins to flash
• hold down (> 1.6 s.) the programming button (Prog.) of the smart switch again.
The memory of the receiver is now deleted entirely and the LED (Prog.) lights up for 4 s. to confirm.
• exit programming mode by briefly pressing (< 1.6 s.) the programming button (Prog.).
Please note:
You can never terminate the connection between the control button of the smart switch itself
and the switching contact.
4. TROUBLESHOOTING
If your smart switch does not function as described in this manual, you can carry out a number of extra checks:
• Check that the mains voltage is connected properly to the smart switch.
• Check that the mains voltage is switched on for the circuit in which you have installed the smart switch.
• Check the operation of the smart switch. Press the programming button at the front of the base. If the indication
LED does not flash, the smart switch is faulty.
• Check the wireless signal strength in the environment using a diagnostics device (05-370). If the reach is
insufficient, move the push button or use a wireless repeater according to the Easywave protocol (05-535)
to increase the range.
• Check – in the case of an existing installation – if the environment of the wireless system has changed, causing
disruptions (metal electrical cabinet, partitions, moved furniture ...). Restore the original situation, if possible.
5. TECHNICAL DATA
Flush-mounting depth
29.5 mm
Dimensions
70 x 70 x 42 mm (HxWxD)
Weight
100 g
Frequency
868.3 MHz
Maximum radio frequency power
5 dBm
Power supply voltage
230 Vac, 50 Hz
Standby consumption
0.38 W
Maximum incandescent lamp load
2,300 W
Maximum load 230 V LED lamps and economy lamps (CFLi)
100 W
Maximum fluorescent lamp load
600 W
Maximum load for low voltage halogen lamps
600 VA
Protection degree
IP 41
Ambient temperature during operation
0 – 35°C
Ambient temperature during storage and transport
-25 – 70°C
Marking
CE marked
6. WARNINGS REGARDING INSTALLATION
• The installation should be carried out by a registered installer and in compliance with the applicable regulations.
• This user manual should be presented to the user. It should be included in the electrical installation file, and
it should be passed on to any new owners. Additional copies are available on the Niko website or via the Niko
support service. The latest manual for this product is available on the Niko website at any time.
• During installation, the following should be taken into account (non-exhaustive list):
- the applicable laws, standards and regulations.
- the technology available at the time of installation.
- this user manual, which only states general regulations and should therefore be read within the scope
of each specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find
the EU declaration of conformity regarding this product at www.niko.eu.
7. NIKO SUPPORT
In case of doubt or if you want to exchange the product in case of a defect, contact your wholesaler or the
Niko support service:
• Belgium: +32 3 778 90 80
• The Netherlands: +31 880 15 96 10
Contact details and more information can be found at www.niko.eu under the “Help and advice” section.
8. WARRANTY PROVISIONS
• The warranty period is four years from the date of delivery. The delivery date is the invoice date of purchase
of the product by the consumer. If there is no invoice, the date of production applies.
• The consumer is obliged to inform Niko in writing about the non-conformity, within two months of noticing
the defect.
• In case of a non-conformity, the consumer only has the right to a product repair or replacement free of charge,
which shall be decided by Niko.
• Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless
use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance
instructions or an external cause, such as damage due to moisture or overvoltage.
• The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
Niko nv hereby declares that the type of radio equipment 410-00100, 410-00110, 410-00200 and 410-00210
complies with Directive 1999/5/EC and Directive 2014/53/EU.
The full text of the EU Declaration of Conformity can be found on www.niko.eu.
This product cannot be deposited in the unsorted waste. Take your discarded product to a recycling centre or a recognised
collection point. Just like producers and importers, you too play an important role in the promotion of sorting, recycling and
reuse of waste electrical and electronic equipment. To finance the rubbish collection and waste treatment, the government
levies recycling charges in certain cases (included in the price of this product).