Nice MC824HHS, Instructions And Warnings For Installation And Use

Page: 25 / 28

ENGLISH – 25
&
&
INSTRUCTIONS AND WARNINGS
Before using the automation for the first time, ask the installer to
explain the origin of any residual risks and take a few minutes to
read this instruction manual and warnings for the user given to you
by the installer. Store the manual for future reference and hand it to
the new owner when transferring the automation.
a
WARNING!
Your automation is a machine that faithfully executes
commands imparted by the user. Negligence and
improper use may lead to dangerous situations:
–
do not manoeuvre the gate if there are people, animals or
objects within its range of operation
–
it is strictly forbidden to touch parts of the automation
while it is moving
–
the photocells should not be regarded as actual safety
devices but only as auxiliary safety devices. They are
designed using highly reliable technology, but in extreme
conditions may be subject to malfunctions or potential
faults, and in certain cases these faults might not be
immediately evident
–
periodically check that the photocells work properly.
a
IT IS STRICTLY FORBIDDEN to transit while the
automation is closing! Transit is allowed only if the
automation is fully open and stationary.
a
CHILDREN
An automation system guarantees a high degree
of safety. With its detection systems, it can control
and guarantee the gate’s movement in the presence
of people or objects. It is nonetheless advisable to
forbid children from playing near the automation
and not to leave remote controls near them to
prevent any unwanted activation of the system. The
automation is not a toy!
The product is not intended for use by persons,
including children, with limited physical, sensory
or mental capacities, or who lack experience or
knowledge, unless supervised or trained in the use
of the product by a person responsible for their
safety.
Anomalies: if the automation appears to behave strangely,
disconnect the power supply to the automation and manually
unlock the motor (consult the respective instruction manual)
to manoeuvre the gate manually. Do not perform any repairs
personally, but contact your trusted installer.
l
Do not modify the system or the programming
and adjustment parameters of the control unit:
your installer is exclusively responsible for these
operations.
Failure or power outage: while waiting for your installer to
intervene or the power supply to be restored, if the system is not
equipped with back-up batteries, the automation can be used
by manually unlocking the motor (consult the relative instruction
manual) and manually moving the gate leaf.
Safety devices out of order: the automation can also be used
when one or more safety devices are defective or out of order.
The automation can be controlled in “
Hold-to-run
” mode in the
following way:
1. send a command to operate the gate, with a transmitter or
key selector, etc. If everything works properly, the gate will
move normally, otherwise proceed as described below
2. within 3 seconds, press the control again and hold it down
3. after roughly 2 seconds, the gate will move in the “ hold-to-
run ” mode, in other words, it will continue moving so long as
the control is held down.
m
If the safety devices are out of order, have the
system repaired as soon as possible by a qualified
technician.
The test, periodic maintenance and any repairs must be documented
by the person carrying out the work and the documents must be
stored by the owner of the automation. The only interventions the
user may carry out periodically include cleaning of the photocell
glass components (use a soft and slightly damp cloth) and removing
any leaves or stones that may obstruct the automation.
m
The user of the automation must manually unlock
the motor before starting any maintenance
operation, to prevent other people from accidentally
manoeuvring the gate (consult the respective
instruction manual).
Maintenance: in order to ensure constant levels of safety and the
longest useful life for the automation, routine maintenance must be
carried out (at least every 6 months).
l
Only qualified personnel is authorised to carry out
checks, maintenance operations and repairs.
Disposal: at the end of its useful life, the automation must be
dismantled by qualified personnel and the materials must be
recycled or disposed of in compliance with the local regulations
in force.
l
If the automation was locked using the “Lock
automation” command, the gate will not move
when a command is sent and the warning light will
emit 9 short flashes.