Nice MC824HHS, Instructions And Warnings For Installation And Use

Page: 11 / 28

ENGLISH – 11
4. LED “ L2 ” flashes: position 0 of M2
–
to command and move motor 2 to position “0” (“ Figure
14 ”): press and hold the f or h button.
Once the position is reached, release the button to stop
the manoeuvre
–
to memorise the position, press and hold the g
button for at least 3 seconds then release it (after 2
seconds LED “
L2
” will remain lit and after the g
button is released, LED “ L3 ” will start flashing)
5. LED “ L3 ” flashes: position SA of M2
–
to command and move motor 2 to position “SA” (“ Figure
14
”): press and hold the f or h button.
Once the position is reached, release the button to stop
the manoeuvre
–
to memorise the position, press and hold the g
button for at least 3 seconds then release it (after 2
seconds LED “ L3 ” will remain lit and after the g
button is released, LED “ L4 ” will start flashing)
6. LED “ L4 ” flashes: position A of M1
–
to command and move motor 1 to
position “A”
(“
Figure
14 ”): press and hold the f or h button.
Once the position is reached, release the button to stop
the manoeuvre
–
to memorise the position, press and hold the g
button for at least 3 seconds then release it (after 2
seconds LED “ L4 ” will remain lit and after the g
button is released, LED “ L5 ” will start flashing)
7.
LED “
L5
” flashes:
position A of M2
–
to command and move motor 2 to position “A” (“ Figure
14 ”): press and hold the f or h button.
Once the position is reached, release the button to stop
the manoeuvre
–
to memorise the position, press and hold the g
button for at least 3 seconds then release it (after 2
seconds LED “ L5 ” will remain lit and after the g
button is released, LED “
L6
” will start flashing)
8. LED “ L6 ” flashes: position SC of M1
–
to command and move motor 1 to position “SC” (“ Figure
14 ”): press and hold the f or h button.
Once the position is reached, release the button to stop
the manoeuvre
–
to memorise the position, press and hold the g
button for at least 3 seconds then release it (after 2
seconds LED “
L6
” will remain lit and after the g
button is released, LED “ L7 ” will start flashing)
9. LED “ L7 ” flashes: position 1 of M1
–
to command and move motor 1 to position “1” (“ Figure
14
”): press and hold the f or h button.
Once the position is reached, release the button to stop
the manoeuvre
–
to memorise the position, press and hold the g
button for at least 3 seconds then release it (after 2
seconds LED “ L7 ” will remain lit and after the g
button is released, LED “ L8 ” will start flashing)
10. LED “ L8 ” flashes: position 1 of M2
–
to command and move motor 2 to position “1” (“ Figure
14 ”): press and hold the f or h button.
Once the position is reached, release the button to stop
the manoeuvre
–
to memorise the position, press and hold the g
button for at least 3 seconds, then release it (after 2
seconds, LED “
L8
” will remain lit; releasing the g
button allows for exiting the manual programming mode).
a
If the system has a single motor only:
–
proceed as described at points 1 and 2
–
at points 3 and 9, press and hold the g button
for at least 3 seconds then release it
–
after 2 seconds, the relative LED will remain lit until the
g button is released. The next LED will then start
flashing.
Do not programme the positions relative to LEDs
L3 (SA of M2), L4 (A of M1) and L6 (SC of M1). To
shift between LEDs, simply press the
f
or
h
button briefly (the LED will flash to signal
the current position).
4.8.3 Learning in mixed mode
m
The user has maximum 10 seconds to press
the buttons consecutively during the learning
procedure. After this time, the procedure terminates
automatically and memorises the changes made up
to that time.
L3
L4
17
To effect the learning procedure in mixed mode:
1. run the self-learning procedure in automatic mode as
described under the “
Learning in automatic mode
”
paragraph
2. simultaneously press and hold the and g buttons
h
3.
release the buttons when LED “
L1
” starts flashing
4. briefly press the f o h button to shift the
flashing LED ( L1…L8 ) to the position to be programmed
5. repeat this last operation for all the other positions to be
modified.
6. To terminate manual learning, press the h button
repeatedly until the flashing LED moves beyond position
“ L8 ”.