background image

FP-AIO-600 and cFP-AIO-600

12

ni.com

in an area, position, or cabinet that prevents accidental or 
unauthorized access to wiring that carries hazardous voltages.

Do 

not

 use the [c]FP-AIO-600 as the only isolating barrier 

between human contact and working voltages higher than 
250 V

rms

.

Operate the [c]FP-AIO-600 only at or below Pollution 
Degree 2. Pollution Degree 2 means that only nonconductive 
pollution occurs in most cases. Occasionally, however, a 
temporary conductivity caused by condensation must be 
expected.

Operate the [c]FP-AIO-600 at or below Measurement 
Category II. Measurement Category II is for measurements 
performed on circuits directly connected to the low-voltage 
installation. This category refers to local-level distribution, 
such as that provided by a standard wall outlet.

Safety Guidelines for Hazardous Locations

The cFP-AIO-600 is suitable for use in Class I, Division 2, Groups 
A, B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC 
T4 and Ex nA IIC T4 hazardous locations; and nonhazardous 
locations only. Follow these guidelines if you are installing the 
cFP-AIO-600 in a potentially explosive environment. Failing to 
follow these guidelines may result in serious injury or death.

Caution

Make sure that all products you use in hazardous 

locations are certified for such use. Refer to the product 
label or visit 

ni.com/certification

, search by 

model number or product line, and click the appropriate 
link in the Certification column.

Caution

Do 

not

 disconnect I/O-side wires or connectors 

unless power has been switched off or the area is known 
to be nonhazardous.

Caution

Do 

not

 remove modules unless power has been 

switched off or the area is known to be nonhazardous.

Caution

Substitution of components may impair 

suitability for Class I, Division 2.

Caution

For Zone 2 applications, install the Compact 

FieldPoint system in an enclosure rated to at least IP 54 
as defined by IEC 60529 and EN 60529.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for FieldPoint cFP-AIO-600























Reviews: