Newland NLS-HR3260 Series User Manual Download Page 53

Page: 53 / 155

【

Enter Setup

】

Chapter 5 Symbologies

Introduction

Every symbology (barcode type) has its own unique attributes. This chapter provides programming

barcodes for configuring the scanner so that it can identify various barcode symbologies. The more

symbologies you enable, the slower your scanner decodes. It is recommended to disable those that are

rarely used to improve the performance of the scanner.

General Settings

Disable All Symbologies

If the

Disable All Symbologies

feature is enabled, the scanner can only identify the programming

barcodes.

【

Disable All Symbologies

】

Enable All Symbologies

If the

Enable All Symbologies

feature is enabled, the scanner can read all compatible barcode

symbologies as well as the programming barcodes.

【

Enable All Symbologies

】

【

Exit Setup

】

Summary of Contents for NLS-HR3260 Series




























































































































































Search results

Summary of Contents for NLS-HR3260 Series

Reviews:

Related manuals for NLS-HR3260 Series

Brands by name

Popular brands

Newland NLS-HR3260 Series, User Manual

Search results

Summary of Contents for NLS-HR3260 Series

Reviews:

Related manuals for NLS-HR3260 Series

Brands by name

Popular brands