background image

 

Good Read Beep (Non-Programming Barcode) ............................................................................. 18

 

Good Read Beep Type ............................................................................................................. 18

 

Good Read Beep Volume ........................................................................................................ 19

 

Good Read Beep (Programming Barcode) ..................................................................................... 19

 

Startup Beep .................................................................................................................................... 19

 

Good Read LED Notification.................................................................................................................. 20

 

Transmit NGR Message ........................................................................................................................ 21

 

Edit NGR Message .......................................................................................................................... 21

 

Scan Mode ............................................................................................................................................. 22

 

Manual Mode ................................................................................................................................... 22

 

Decode Session Timeout ......................................................................................................... 22

 

Auto Sleep ................................................................................................................................ 23

 

Sense Mode ..................................................................................................................................... 24

 

Decode Session Timeout ......................................................................................................... 24

 

Image Stabilization Timeout ..................................................................................................... 25

 

Continue after Good Read ....................................................................................................... 25

 

Timeout between Decodes (Same Barcode) ........................................................................... 26

 

Sensitivity ................................................................................................................................. 27

 

Continuous Mode ............................................................................................................................ 28

 

Decode Session Timeout ......................................................................................................... 28

 

Timeout between Decodes....................................................................................................... 29

 

Factory Defaults ..................................................................................................................................... 30

 

Chapter 3 RS-232 Interface ............................................................................................................................. 31

 

Introduction ............................................................................................................................................ 31

 

RS-232 Parameters ............................................................................................................................... 31

 

Baud Rate ........................................................................................................................................ 32

 

Parity Check .................................................................................................................................... 33

 

Data Bit ............................................................................................................................................ 33

 

Data Bit & Parity Check ................................................................................................................... 33

 

Stop Bit ............................................................................................................................................ 34

 

Hardware Auto Flow Control ........................................................................................................... 35

 

Chapter 4 USB Interface .................................................................................................................................. 36

 

Introduction ............................................................................................................................................ 36

 

Summary of Contents for NLS-HR3260 Series




























































































































































Reviews: