Newland HR3260-CS User Manual Download Page 45

Page: 45 / 165

【

Enter Setup

】

【

Exit Setup

】

Chapter 3 Inquiry Command

Introduction

This chapter provides programming barcodes you may need to obtain device information.

Obtain Scanner Information

You can scan the barcode below to inquire the scanner information (such as model number, serial

number, manufacture date and firmware version). The result will be sent to the Host.

【

Inquire All Information About Scanner

】

Obtain Cradle Information

You can scan the barcode below to inquire the cradle information (such as model number, serial number,

manufacture date and firmware version). The result will be sent to the Host.

【

Inquire All Information About Cradle

】

Summary of Contents for HR3260-CS






































































































































































Search results

Summary of Contents for HR3260-CS

Reviews:

Related manuals for HR3260-CS

Brands by name

Popular brands

Newland HR3260-CS, User Manual

Search results

Summary of Contents for HR3260-CS

Reviews:

Related manuals for HR3260-CS

Brands by name

Popular brands