New Leader AGCO NL4258 Operator'S Manual Download Page 64

Page: 64 / 134

- 64 -

www.NewLeader.com

(800) 363-1771

312521-AA-C

NL4258/4330G4 EDGE

Troubleshooting

Symptom:

Reason:

Correction:

Spinner will not run

Defective Spinner Control Valve

Replace spinner control valve cartridge and coil�

No voltage at valve

Verify spinner switch is on�

Verify spinner enable is checked�

Verify controller has a target spinner RPM entered�

Check WSM 7�5 amp fuse is not blown�

Verify spinner control harness is not damaged�

Verify system was configured as Basic independent.

No hydraulic flow

Verify hydraulics are on�

Pressure test pump - replace as needed�

System is going over relief - test & replace as needed�

Spinner will not shut off

Defective spinner control valve

Replace spinner control valve cartridge�

Control valve is manually overrode

Loosen jam nut on control valve cartridge and back set
screw out until spinner stops�

Spinner runs erratic

Defective spinner control valve

Replace spinner control valve cartridge�

Spinner speed sensor harness
failure

Replace sensor harness�

Spinner speed sensor not properly
installed

Adjust sensor so that gap between sensor and fin mounting

bolt is less than 1/8”�

Spinner speed drops off
when turning around

Improper control settings

Verify PWM control is set properly (HOLD for gear pumps,
CONTROL for variable displacement)�

Spinner speed does not
hit target

Defective spinner control valve

Replace spinner control valve cartridge�

Pump failure

Flow and pressure test pump�

Spinner speed sensor not properly
installed

Adjust sensor so that gap between sensor and fin mounting

bolt is less than 1/8”�

Hydraulic flow dropping off

Adjust settings and speed� Pressure test relief (adjust or
replace as needed)�

Spinner speed sensor harness
failure

Replace sensor harness�

Spinner speed sensor failure

Replace spinner speed sensor�

Conveyor will not run

Defective conveyor control valve

Replace conveyor valve cartridge�

No voltage at valve

Verify bin switch and master switches on�

Verify in controller that target rate, density, ground speed
and a CFR number are all entered�

Check WSM 7�5 amp fuse is not blown�

Verify conveyor control harness is not damaged�

No hydraulic flow

Verify hydraulics are on�

Pressure test pump - replace as needed�

System is going over relief - test & replace as needed�

Conveyor is going over relief - test & replace as needed�

Summary of Contents for AGCO NL4258







































































































































Search results

Summary of Contents for AGCO NL4258

Reviews:

Related manuals for AGCO NL4258

Brands by name

Popular brands

New Leader AGCO NL4258, Operator'S Manual

Search results

Summary of Contents for AGCO NL4258

Reviews:

Related manuals for AGCO NL4258

Brands by name

Popular brands