New Leader AGCO NL4258 Operator'S Manual Download Page 21

Page: 21 / 134

- 21 -

NL4258/4330G4 EDGE

www.NewLeader.com
(800) 363-1771

312521-AA-C

Safety Decals

5. WARNING: MOVING PART HAZARD

To prevent death or serious injury:

• Close and secure guards before operating machine�

• Do not stand or climb on machine�

• Disconnect and lockout power source before adjusting or servicing�

• Keep hands, feet and hair away from moving parts�

6. DANGER: GUARD IS MISSING WHEN THIS IS VISIBLE

To prevent death or serious injury:

• Do not operate this unit without guard in place�

4. WARNING: FALLING HAZARD

To prevent death, serious injury or machine damage:

• Do not climb or stand on guard�

• Do not place objects on fenders�

• Keep off fenders� They are not intended to carry loads�

Summary of Contents for AGCO NL4258







































































































































Search results

Summary of Contents for AGCO NL4258

Reviews:

Related manuals for AGCO NL4258

Brands by name

Popular brands

New Leader AGCO NL4258, Operator'S Manual

Search results

Summary of Contents for AGCO NL4258

Reviews:

Related manuals for AGCO NL4258

Brands by name

Popular brands