manualshive.com logo in svg

New England Arbors Aberdeen, Assembly Manual, Page: 13 / 26

Share
Download
New England Arbors Aberdeen Assembly Manual Download Page 13

Main Support Beam Assembly 

1

1

2

STEP FOUR

At this stage, the columns should be properly

installed as per the following illustration,

with the columns 133” in. (338 cm) apart.

Also, notice that the holes at the top of each

post should be facing the same direction.

130 1/8 in.

330.5 cm.

Critical Note:

Note the location of the pre-drilled hole on main support beams

 as pictured aside. These holes will align with the hole on the posts.

Both ends of main support beam section should extend approximately

6” (15.2 cm) over the pressure treated wood.

Insert and center one 2x6x12’ (4x15x300cm) pressure treated wood

into a main support beam section followed by the joiner and

another main support beam section. 

Glue and attach the Decorative End Caps onto the ends as shown.

www.newenglandarbors.com

www.newenglandarbors.co.uk

133 in.

338 cm.

134 in. (340.4 cm.)

Between Faces

133 in. (338 cm.)

Between Tangent Surfaces

130 1/8 in. (330.5 cm.)

Between Post Base Trims

13

12 x 12 Round Post Louvered Pergola

Summary of Contents for Aberdeen



























Reviews:

No comments