NETGEAR R6200v2 User Manual Download Page 9

Page: 9 / 131

Hardware Setup

R6200v2 Smart WiFi Router

Front and Side Panels

The router front and side panels have the status LEDs and buttons shown in the following
figure.

LEDs

WiFi On/Off button

WPS button

Figure 2. Router front and side view

Table 1. Front panel LED descriptions

LED

Description

Power

•

Solid amber

. The router is starting.

•

Blinking amber

. The firmware is upgrading, or the Reset button was pressed.

•

Solid green

. The router is ready.

•

Blinking green

. The firmware is corrupted. Visit

www.netgear.com/support

•

Off

. Power is not supplied to the router.

Internet

•

Solid green

. The Internet connection is ready.

•

Solid amber

. The Ethernet cable connection to the modem has been detected.

•

Off

. No Ethernet cable is connected to the modem.

Wireless

•

Solid blue

. The wireless radio is operating in either 2.4 GHz or 5 GHz mode.

•

Blinking

. The router is in WPS mode.

•

Off

. The wireless radios are off for both 2.4 GHz and 5 GHz.

USB

•

Solid blue

. The router has accepted the USB device. The USB device is ready to be used.

•

Blinking blue

. A USB device is plugged in and is trying to connect.

•

Off

. No USB device is connected;, or someone clicked the Safely Remove Hardware button,

and it is now safe to remove the attached USB device.

Summary of Contents for R6200v2




































































































































Search results

Summary of Contents for R6200v2

Reviews:

Related manuals for R6200v2

Brands by name

Popular brands

NETGEAR R6200v2, User Manual

Search results

Summary of Contents for R6200v2

Reviews:

Related manuals for R6200v2

Brands by name

Popular brands