NetComm 3G21WE User Manual Download

Page: 47 / 50

Etisalat HSPA+ WiFi Router

USER GUIDE

Field

Description

Manufacturer

The manufacturer of the embedded 3G module.

Model

The model name of the embedded 3G module.

FW Rev.

The firmware version of the 3G module.

IMEI

The IMeI (International Mobile equipment Identity) is a 15 digit number that
is used to identify a mobile device on a network.

FSN

Factory Serial Number of the 3G module.

IMSI

The IMSI (International Mobile Subscriber Identity) is a unique 15-digit
number used to identify an individual user on a UMTS network.

HW Rev.

The hardware version of the 3G module.

System Mode

WCDMA/Europe CMDA 2000 / America

WCDMA band

The 3G radio frequency band which supports dual-band UTMS/HSDPA/HSUPA
frequencies (850/2100 MHz), IMT2000 is 2100 MHz, WCDMA800 is 850MHz

WCDMA

channel

The 3G channel.

MM (CS) state

Circuit Switching state

Signal Strength

The 3G signal strength in dBm.

Signal level

in dBm

-109 ~ -103

-101 ~ -93

-91 ~ -87

-85 ~ -79

-77 ~ -52

5 Signal

bars

LED

Low

Medium

High

7.4

STATISTICS

These screens provide detailed information for:

•

Local Area Network (LAN) and Wireless Local Area Network (WLAN)

•

3G Interfaces

NOTE:

These statistics page refresh every 15 seconds

7.4.1 LAN STATISTICS

This screen displays statistics for the Ethernet and Wireless LAN interfaces.

7.4.2 3G STATISTICS

Click Etisalat™ network in the Statistics submenu to display the screen below.

Diagnostics

Summary of Contents for 3G21WE



















































Search results

Summary of Contents for 3G21WE

Reviews:

Related manuals for 3G21WE

Brands by name

Popular brands

NetComm 3G21WE, User Manual

Search results

Summary of Contents for 3G21WE

Reviews:

Related manuals for 3G21WE

Brands by name

Popular brands