Ness D24, Installation & Programming Manual

Page: 5 / 60

5
neSS D24 Control Panel - inStallation & PrograMMing Manual
+
12
V
+
12
V
+
12
V
+
12
V
+
12
V
+
12
V
+
12
V
+
12
V
+
12
V
0V 0V 0V 0V 0V 0V 0V
0V
0V
105-399
D24 Po wer Board
0V +12V
0V +12V +12V 0V +12V 0V +12V 0V 0V +12V 0V +12V 0V +12V +12V 0V
EA
RT
H
17
V
AC
AU
X
+
12
V
0V
N
C
CO
M
N
O
RE
SE
T
ST
RO
BE
SR
N
A
SR
N
B
SR
N
+
TA
M
P
C
KE
Y
C
+
12
V
+
12
V
CL
K
0V 0V
DA
TA
KEYPAD
RE
SE
T
+
ST
RO
BE
+
Z1 Z5 Z9 Z1
3
Z1
7
Z2
1
C C C C C C Z2 Z6 Z1
0
Z1
4
Z1
8
Z2
2
Z3 Z7 Z1
1
Z1
5
Z1
9
Z2
3
C C C C C C Z4 Z8 Z1
2
Z1
6
Z2
0
Z2
4
J3
RADI
O
PHONE
J1
J6
TA
MPER
LISTEN
BA
T
TERY
NES
S SECURITY PRODUCTS
105-232 D24
RELA
Y
HEA
TSINK
12V 7Ah Battery
Rear Tamper Switch
Rear Tamper Switch
Document holder
Battery cradle
Lid Tamper Switch
Bolt
Bolt post
Lid
Speed nut
Circlip
Base
Lid Tamper switch
Power Board
(Screwed to bottom of base)
Housing lid bolts x2
Side cable entry
Square duct knockout
Top mounting
hole x2 (Keyhole)
Board Clip Retainers x2
(adjustable position)
Bottom mounting
hole x2 (Slotted)
Top cable entry
Square duct knockout
Rear cable entry
B
B
iNSTallaTiON & POwEr uP PrOCEdurES
the control panel housing should be mounted in a location that is within a
protected zone of the premises.
install the D24 panel as follows:
InstallatIOn
1. insert the rear tamper Switch in the mounting hole in the base.
2. Screw the base to the wall using at least 4 fasteners. if mounting on an uneven surface,
make sure the rear tamper switch is correctly pushing in.
3. insert the adjustable Board Clip retainers in the positions as shown.
4. insert the D24 Board. Fit the Slots “a” first, followed by slots “B”. the board should be
mounted in the second highest position.
5. attach the supplied Speed nuts to both Bolt Posts.
6. Fit the removable terminal strips on the two rows of pins on the D24 Board.
7. Fit the housing lid tamper Switch behind the right hand bolt post.
8. Connect both tamper switches using the tamper leads supplied and plug the tamper
lead assembly into the J1 header on the D24 board.
9. Fit the backup battery in the battery cradle. the battery terminals should be at top.
10. Complete the wiring of detection devices, sirens, telephone lead, etc.
11. Power up and program the control panel.
13. Before exiting program mode, fit the housing lid. Clip the lid at the top first then swing it
down. Fasten the lid with the 2 bolts supplied. (the bolts can be made captive to the lid
using the supplied circlips).
pOwerIng up
after wiring, power up as follows:
1. Make sure the J1 pins are open,
(remove the link or unseal the lid
tamper switch.) this condition
forces the panel to enter installer
program mode on power up.
2. Connect the battery, (observe
correct polarity), and connect the
plug pack.
3. the keypad will give 3 beeps
and the panel will be in installer
Program mode, (Program icon is
flashing).
4. replace the J1 link or seal the lid
tamper.
5. Program the panel as required.
note 1: the panel will not exit
program mode unless user Code
1 (P1e) is programmed, all other
programming options are optional.
note 2: if the J1 link is open (or lid
tamper unsealed) when you exit
program mode, the tamper alarm will
trigger.