37
N E S S r a d i O
neSS D24 Control Panel - inStallation & PrograMMing Manual
OPTION No DESCRIPTION
OPTION
P83E
P831E
P84E
P841E
CLEAR Radio Keys 1-8
Program Radio Keys 1-8
CLEAR Radio Devices 1-8
Program Radio Devices 1-8
Select 1E - 8E
Select 1E - 8E
Select 1E - 8E
Select 1E - 8E
radiO KEy PrOgrammiNg
a total of eight ness 100-664 radio Keys can be programmed. the radio Keys
operate in conjunction with D24 user Codes 1 to 8 and, if monitored, are reported
as user Codes 1–8 to the central station.
to Program:
Press
P831e
, then select a radio key to program. 1e–8e.
on the radio key to be programmed, press and hold the
PanIc button for 8 seconds.
• The MEMORY light will flash during the 8 second ‘Learn’ transmission. If the Radio
Key is accepted, the MEMORY light will turn on steady and 3 beeps will sound.
• If the MEMORY light does not flash, the Radio Key is already programmed and
must be cleared before it can be programmed again.
to clear (delete) a radIo key:
Press
P83e
Lights 1–8 will show which Radio Keys are currently programmed.
Press
1e–8e
Press the Radio Key number followed by E.
P83e, P831e
prOgraM MOde leVel:
Installer, Remote by PC
FaCtOrY deFault:
No Radio Keys programmed
nOtes:
• The 8 Radio Codes operate independently, they
do not replace any keypad codes.
• Radio Key programming is done by ‘learning’
the code by radio.
• If a Radio Key is lost or misplaced, its use
can be prevented by clearing that Radio Code
using the keypad.
• Radio Keys are allocated to User Codes 1–8,
so that Open/Close reports are identified by
user number when the control panel is central
station monitored. (If Open/Close reports are
enabled).
related OptIOns:
P82E 3E Enable Radio Interface
P34E 2E Enable Siren Chirps
radiO dEviCE PrOgrammiNg
a total of eight ness radio Devices can be programmed.
a radio Device is any type of ness transmitter including radio Pir, radio reed
Switches, radio Smoke Detector.
to Program:
Press
P841e
, then select a radio device to program. 1e–8e.
trigger the radio device (or insert the battery).
• If the Radio Device is accepted, the MEMORY light will turn on steady and 3
beeps will sound.
• If the MEMORY light does not flash, the Radio Device is already programmed and
must be cleared before it can be programmed again.
• When the device has been programmed, remove its battery to prevent it from
transmitting while you program the next device.
Remember to replace all the
batteries when finished programming.
to clear (delete) a radIo devIce:
Press
P84e
Lights 1–8 will show which Radio Devices are currently programmed.
Press
1e–8e
Press the Radio Device number followed by E.
P84e, P841e
prOgraM MOde leVel:
Installer, Remote by PC
FaCtOrY deFault:
No Radio Devices programmed
nOtes:
• Radio Device programming is done by
‘learning’ the code by radio.
• If a Radio Device is lost or misplaced, it’s use
can be prevented by clearing that Radio Code
using the keypad
• The device’s ENCR link (if fitted) must be off.
This applies to the 100-663 Radio PIR and the
100-662 Radio Reed Sw.
related OptIOns:
P82E 3E Enable Radio Interface
the optional 100–200 Ness
radio Interface is required
for radio operation.
Insert battery to send
the learn message
Press 3 times to
send the learn
message
Press and hold
Panic to send the
learn message
