Ness D24 Installation & Programming Manual Download Page 47

Page: 47 / 60

O P E r a T i O N

neSS D24 Control Panel - inStallation & PrograMMing Manual

HoW to VIeW memorY

. When the

MEMORY

icon is flashing to indicate there is a new alarm in memory,

pressing

will display an icon, (for example, Zone, tamper, System

etc), and a number to indicate the type of alarm.

. in normal idle mode, (system is disarmed with the

ZONE

icon displayed),

the memory history can be displayed in sequence.

to view the Memory history,

Press...

the

MEMORY

icon will turn on.

then press...

[repeat presses]. at each step, the keypad icons will

display past events. the Zone, tamper, System and Power icons will indicate
what type of events are being displayed.

Memory is displayed backwards from most recent event to the end of
memory. the past 50 events are stored.

Press

to exit the Memory menu.

eVents IndICated BY KeYpad ICOns:

ICoN

eVeNt

MEMORY

events are from memory

ZONE

1–24

[flashing]

Zone alarms

TAMPER

1–5

tamper alarms

SYSTEM

1–8

System alarms

POWER

1–0

Power alarms

1–24

[flashing]

Fire Zone alarm

ARM

arm

ZONE

Disarm

[slow flash]

Monitor Mode

area 1 arm

area 2 arm

area 3 arm

[slow flash]

area 1 Monitor Mode

[slow flash]

area 2 Monitor Mode

Panel is Disarmed

(All zones are sealed).

Most recent event:

- Zone 2 alarm.

Next most recent event:

- Panel was Armed.

Next most recent event:

- Mains power failure.

...etc...Up to 50 events in memory.

to exit Memory mode.

ZONE

MEMORY

ZONE

Press...

VIEW

Press...

VIEW

ARM

POWER

Press

example: how to view Memory
and the types of events that might
be shown.

Summary of Contents for D24





























































Search results

Summary of Contents for D24

Reviews:

Related manuals for D24

Brands by name

Popular brands

Ness D24, Installation & Programming Manual

Search results

Summary of Contents for D24

Reviews:

Related manuals for D24

Brands by name

Popular brands