Neousys Technology Nuvo-5095GC Series User Manual Download Page 70

Page: 70 / 97

Nuvo-5095GC Series User’s Manual

4.1.2 SATA Port Configuration

The SATA controller of Nuvo-5095GC series supports two operating modes:

AHCI

and

RAID

mode.

AHCI

mode, which exposes SATA's advanced capabilities such as hot

swapping and native command queuing, is supported in most of modern operating systems.

RAID

mode provides a more reliable data storage (RAID 1/5/10) or a higher disk access

throughput (RAID 0/5/10).

The RAID feature is built in Intel Q170 chipset with BIOS support. No additional H/W or

driver is needed to use RAID function. You can configure the RAID volume during BIOS

POST. Please refer to section 4.3 for detail.

To configure SATA controller operating mode:

1. When Nuvo-5095GC controller boots up, press F2 to enter BIOS setup utility.

2. Go to

[Advanced]



[SATA Configuration]

3. Set the

[SATA Mode Selection]

option to a proper mode for your Nuvo-5095GC

controller.

Summary of Contents for Nuvo-5095GC Series




























































































Search results

Summary of Contents for Nuvo-5095GC Series

Reviews:

Related manuals for Nuvo-5095GC Series

Brands by name

Popular brands

Neousys Technology Nuvo-5095GC Series, User Manual

Search results

Summary of Contents for Nuvo-5095GC Series

Reviews:

Related manuals for Nuvo-5095GC Series

Brands by name

Popular brands