manualshive.com logo in svg

NEC switch, User Manual

The NEC switch provides seamless network connectivity and efficient data transfer. Simplify your networking setup with this reliable and high-performance switch. Unlock its full potential by downloading the comprehensive User Manual for free from our website, ensuring smooth operations and maximum utilization of this exceptional product.

Share
Download
background image

CHAPTER  3    CPU  ARCHITECTURE

User’s Manual  U12978EJ3V0UD

41

(a) Interrupt enable flag (IE)

This flag controls interrupt request acknowledgment operations of the CPU.

When 0, the IE flag is set to the interrupt disabled status (DI), and interrupt requests other than non-

maskable interrupts are all disabled.

When 1, the IE flag is set to the interrupt enabled status (EI).  Interrupt request acknowledgment enable is

controlled by the interrupt mask flag corresponding to each interrupt source.

The IE flag is reset (0) upon DI instruction execution or interrupt acknowledgment and is set (1) upon EI

instruction execution.

(b) Zero flag (Z)

When the operation result is zero, this flag is set (1).  It is reset (0) in all other cases.

(c) Auxiliary carry flag (AC)

If the operation result has a carry from bit 3 or a borrow at bit 3, this flag is set (1).  It is reset (0) in all other

cases.

(d) Carry flag (CY)

This flag stores overflow and underflow upon add/subtract instruction execution.  It stores the shift-out

value upon rotate instruction execution and functions as a bit accumulator during bit manipulation

instruction execution.

Summary of Contents for switch











































































































































































































































Reviews:

No comments

Related manuals for switch

ABB i-bus KNX IPR/S 3.5.1 Product Manual preview
i-bus KNX IPR/S 3.5.1
Brand: ABB Pages: 44
F-SECURE SENSE Quick Manual preview
SENSE
Brand: F-SECURE Pages: 19
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Brand: Ruckus Wireless Pages: 56
Ubiquiti PowerBeam AC Gen2 Quick Start Manual preview
PowerBeam AC Gen2
Brand: Ubiquiti Pages: 22
Rosewill RC-402 User Manual preview
RC-402
Brand: Rosewill Pages: 3
ICP DAS USA ZT-2024 Quick Start Manual preview
ZT-2024
Brand: ICP DAS USA Pages: 8
AC&NC JetStor NAS 724UX User Manual preview
JetStor NAS 724UX
Brand: AC&NC Pages: 117
Trend Micro IPS Pro-Module-24C-GE-BP-TM Quick Setup Manual preview
IPS Pro-Module-24C-GE-BP-TM
Brand: Trend Micro Pages: 3
Cabletron Systems CyberSWITCH CSX101 User'S Information Manual preview
CyberSWITCH CSX101
Brand: Cabletron Systems Pages: 72
B+B SmartWorx SPECTRE v3 LTE User Manual preview
SPECTRE v3 LTE
Brand: B+B SmartWorx Pages: 50
Cradlepoint MBR900 Quick Start Manual preview
MBR900
Brand: Cradlepoint Pages: 2
JAKA MiniCab Hardware User Manual preview
MiniCab
Brand: JAKA Pages: 37
Socket CF Card User Manual preview
CF Card
Brand: Socket Pages: 28
Sun Microsystems McDATA Eclipse 1620 Release Notes preview
McDATA Eclipse 1620
Brand: Sun Microsystems Pages: 9
Tripp Lite N002-025-GY Specification Sheet preview
N002-025-GY
Brand: Tripp Lite Pages: 3
Digital Equipment ChannelWorks Network Installer Manual preview
ChannelWorks
Brand: Digital Equipment Pages: 90
Westermo Viper-012 User Manual preview
Viper-012
Brand: Westermo Pages: 22
H3C MSR-20-21 ROUTER Installation Manual preview
MSR-20-21 ROUTER
Brand: H3C Pages: 83

Brands by name

Popular brands

Load more brands