NEC switch User Manual Download

Page: 103 / 234

CHAPTER 8 USB FUNCTION

User’s Manual U12978EJ3V0UD

103

(4) Receive data bank

(a) Receive data PID (USBRD)

This is the receive data packet ID area. The data input to the data/handshake PID compare register

(DIDCMP) is stored here.

USBRD is read with an 8-bit memory manipulation instruction.

RESET input sets USBRD to 00H.

(b) Receive data address (USBR0 to USBR7)

This is an 8-byte register that stores the data/handshake packet transferred from the host.

USBR0 to USBR7 are read with an 8-bit memory manipulation instruction.

If the following combinations are used, they are read with a 16-bit memory manipulation instruction.

•

USBR10: USBR0 and USBR1

•

USBR32: USBR2 and USBR3

•

USBR54: USBR4 and USBR5

•

USBR76: USBR6 and USBR7

RESET input makes USBR0 to USBR7 undefined.

Figure 8-5. Configuration of Receive Data Bank

10H

07H

06H

05H

04H

03H

02H

01H

00H

11H

12H

13H

14H

15H

16H

17H

18H

USBRD

USBR0

USBR1

USBR2

USBR3

USBR4

USBR5

USBR6

USBR7

USBPOW address

USBPOB address

Symbol

ID area

Data area (8 bytes)

The operation during reception appears as follows.

8th byte

1st byte

USBT00

USBT07











SETUP

DATA0

ACK

Packet from host controller

Response packet

USBT00

USBT07











OUT

DATA1

ACK

8th byte

1st byte

The data packet from the host controller is stored in the USBT00 to USBT07 registers.

Summary of Contents for switch











































































































































































































































Search results

Summary of Contents for switch

Reviews:

Related manuals for switch

Brands by name

Popular brands

NEC switch, User Manual

Search results

Summary of Contents for switch

Reviews:

Related manuals for switch

Brands by name

Popular brands