NEC PD75P3116 Datasheet Download

Page: 13 / 70

PD75P3116

Data Sheet U11369EJ3V0DS

3.4 Recommended Connection of Unused Pins

Table 3-1. List of Unused Pin Connections

Recommended Connection

P00/INT4

Connect to Vss or V

P01/SCK

Input:

Independently connect to Vss or V

via a resistor.

P02/SO/SB0

Output: Leave open.

P03/SI/SB1

Connect to Vss.

P10/INT0 and P11/INT1

Connect to Vss or V

P12/TI1/TI2/INT2

P13/TI0

P20/PTO0

Input:

Independently connect to Vss or V

via a resistor.

P21/PTO1

Output: Leave open.

P22/PTO2/PCL

P23/BUZ

P30/LCDCL/MD0

P31/SYNC/MD1

P32/MD2

P33/MD3

P50/D4 to P53/D7

Input:

Connect to Vss.

Output: Connect to Vss.

P60/KR0/D0 to P63/KR3/D3

Input:

Independently connect to Vss or V

via a resistor.

Output: Leave open.

S0 to S15

Leave open.

COM0 to COM3

S16/P93 to S19/P90

Input:

Independently connect to Vss or V

via a resistor.

S20/P83 to S23/P80

Output: Leave open.

LC0

to V

LC2

Connect to Vss.

BIAS

Connect to Vss only when none of V

LC0

, V

LC1

or V

LC2

is used.

In other cases, leave open.

XT1

Note

Connect to Vss.

XT2

Note

Leave open.

Always connect to V

directly.

Note

When the subsystem clock is not used, select SOS.0 = 1 (on-chip feedback

resistor not used).

Summary of Contents for PD75P3116







































































Search results

Summary of Contents for PD75P3116

Reviews:

Related manuals for PD75P3116

Brands by name

Popular brands

NEC PD75P3116, Datasheet

Search results

Summary of Contents for PD75P3116

Reviews:

Related manuals for PD75P3116

Brands by name

Popular brands