112
Appendix
Error Code
Error message
Description
577
IMB:Security Battery Event
A Battery Tamper event has been detected with the IMB.
581
IMB:Security Enclosure Not Armed
IMB security not armed.
582
IMB:Physical Marriage Tamper
The IMB has detected a break of the Marriage with the
projector.
583
IMB:Logical Marriage Tamper
The IMB has detected an error with the verification of the
Marriage with the projector.
584
IMB:Marriage NOT Active
The IMB has not established a marriage with the projector
586
IMB:Service Door Tamper
Latched service door tamper condition on IMB
588
IMB:Security Battery Low Warning
Close to “(577) IMB: Security Battery Event”.
700
OPT Comm Fail
Failed to communicate with slave MCU.
701
OPT Status Fail
Slave MCU is in unexpected status.
703
OPT Comm Ack Fail
Slave fails to execute the command.
740
SensorFail Inlet
Failed to read inlet sensor.
741
SensorFail DMD
Failed to read DMD sensor.
750
OverTemp.DMD Precaution
Set inside temperature (DMD) is close to over
temperature.
751
OverTemp.Inlet Precaution
Set inside temperature (Inlet) is close to over temperature.
760
OverTemp.DMD
Set inside temperature (DMD) is abnormal.
761
OverTemp.Inlet
Set inside temperature (Inlet) is abnormal.
762
OverTemp.Light
Set inside temperature (Light) is abnormal.
783
EepromFail
Slave MCU failed to read back all of data from EEPROM
on slave MCU board due to unexpected data or
something.
(Slave board internal abnormality)
791
FanInitError
Failed to initialize fans.
792
ExGpioFail
Failed to control the signal connecting to Ballast.
(Slave board internal abnormality)
800
Fan15 Stop
Fan15 has stopped.
801
Fan16 Stop
Fan16 has stopped.
802
Pump Stop
Pump has stopped.
804
PhosphorWheel Stop
Phosphor Wheel has stopped.
805
Diffuser1 Wheel Stop
Diffuser1 Wheel has stopped.
806
Fan17 Stop
Fan17 has stopped.
810
Fan15 Stop Precaution
Fan15 Stop Precaution
811
Fan16 Stop Precaution
Fan16 Stop Precaution
812
Pump Stop Precaution
Pump Stop Precaution
814
PhosphorWheel Stop Precaution
Phosphor Wheel Stop Precaution
815
Diffuser1 Wheel Stop Precaution
Diffuser1 Wheel Stop Precaution
816
Fan17 Stop Precaution
Fan17 Stop Precaution
906
LD Version Read Fail
Failed to read Laser Driver Software version.
913
TiltDegreeOver
Projector tilt degree is out of spec.
To clear this warning, turn off and AC-OFF the projector,
then setup projector with proper tilt angle within the spec.
914
LowerTemp
Set inside temperature (Inlet) is lower temperature.
933
SensorFail PhosphorWheel
Set inside temperature (Phosphor Wheel) is abnormal.
953
OverTemp.PhosphorWheel Precaution
Set inside temperature (Phosphor Wheel) is close to over
temperature.
973
OverTemp.PhosphorWheel
Set inside temperature (Phosphor Wheel) is abnormal.
982
ColorSensorFail
Failed to control color sensor.
984
GSensorError
Failed to control G-sensor.
985
LD CommError
In I2C communication between slave uC and LD (Laser
Driver) uC, no ack from LD uC.
(Slave uC: I2C slave, LD uC: I2C host)
988
LensInstallSWOpen
Lens install switch is open.
989
BrightnessLow
Brightness has lowered.
