manualshive.com logo in svg

NEC 78K0S/KA1+, User Manual

Introducing the NEC 78K0S/KA1+: A versatile microcontroller offering stellar performance. For a comprehensive understanding of its features and functionalities, grab our Preliminary User's Manual - available for free download on our website. Unlock the full potential of your device today! manualshive.com

Share
Download
background image

CHAPTER  11   SERIAL  INTERFACE  UART6 

User’s Manual  U16898EJ3V0UD 

206 

(i)  SBF reception  

When the device is incorporated in LIN, the SBF (Synchronous Break Field) reception control function is 
used for reception.  For the reception operation of LIN, see 

Figure 11-2  LIN Reception Operation

. 

Reception is enabled when bit 7 (POWER6) of asynchronous serial interface operation mode register 6 
(ASIM6) is set to 1 and then bit 5 (RXE6) of ASIM6 is set to 1.  SBF reception is enabled when bit 6 (SBRT6) 
of asynchronous serial interface control register 6 (ASICL6) is set to 1.  In the SBF reception enabled status, 
the R

X

D6 pin is sampled and the start bit is detected in the same manner as the normal reception enable 

status. 
When the start bit has been detected, reception is started, and serial data is sequentially stored in the 
receive shift register 6 (RXS6) at the set baud rate.  When the stop bit is received and if the width of SBF is 
11 bits or more, a reception completion interrupt request (INTSR6) is generated as normal processing.  At 
this time, the SBRF6 and SBRT6 bits are automatically cleared, and SBF reception ends.  Detection of 
errors, such as OVE6, PE6, and FE6 (bits 0 to 2 of asynchronous serial interface reception error status 
register 6 (ASIS6)) is suppressed, and error detection processing of UART communication is not performed.  
In addition, data transfer between receive shift register 6 (RXS6) and receive buffer register 6 (RXB6) is not 
performed, and the reset value of FFH is retained.  If the width of SBF is 10 bits or less, an interrupt does not 
occur as error processing after the stop bit has been received, and the SBF reception mode is restored.  In 
this case, the SBRF6 and SBRT6 bits are not cleared.  

 

Figure 11-23.  SBF Reception 

 

1.  Normal SBF reception (stop bit is detected with a width of more than 10.5 bits) 

 

R

X

D6

SBRT6

/SBRF6

INTSR6

1

2

3

4

5

6

7

8

9

10

11

 

 

2.  SBF reception error (stop bit is detected with a width of 10.5 bits or less) 

 

R

X

D6

SBRT6

/SBRF6

INTSR6

1

2

3

4

5

6

7

8

9

10

“0”

 

 

Remark

  R

X

D6: R

X

D6 pin (input) 

 

SBRT6:  Bit 6 of asynchronous serial interface control register 6 (ASICL6) 

 

SBRF6:  Bit 7 of ASICL6 

 

INTSR6:  Reception completion interrupt request  

 

Summary of Contents for 78K0S/KA1+



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 78K0S/KA1+

Balmar Max Charge MC-624 Installation And Operator'S Manual preview
Max Charge MC-624
Brand: Balmar Pages: 8
Balmar MAX CHARGE MC-614 Installation And Operation Manual preview
MAX CHARGE MC-614
Brand: Balmar Pages: 20
Gamma Vacuum SPCe User Manual preview
SPCe
Brand: Gamma Vacuum Pages: 25
Gamma DIGITEL MPCq User Manual preview
DIGITEL MPCq
Brand: Gamma Pages: 28
ICM Controls ICM330 Manual preview
ICM330
Brand: ICM Controls Pages: 2
ICM Controls ICM2909 Manual preview
ICM2909
Brand: ICM Controls Pages: 2
Maguire Products GRAVIMETRIC AUGER FEEDER MGF-ST Instruction Manual preview
GRAVIMETRIC AUGER FEEDER MGF-ST
Brand: Maguire Products Pages: 47
Magtrol DSP7000 User Manual preview
DSP7000
Brand: Magtrol Pages: 160
Yamaha CEmarking RCX221 User Manual preview
CEmarking RCX221
Brand: Yamaha Pages: 468
KIPI ecoMAX360P1-C Installation And Operating Manual preview
ecoMAX360P1-C
Brand: KIPI Pages: 44
NOCO Genius CURTIS DC Series Installation Instruction preview
CURTIS DC Series
Brand: NOCO Genius Pages: 2
Xylem Aquavar AB2 Quick Start Manual preview
Aquavar AB2
Brand: Xylem Pages: 2
Danfoss VLT MCD 201 Installation Manual preview
VLT MCD 201
Brand: Danfoss Pages: 36
Oriental motor ASD10A-K Operating Manual preview
ASD10A-K
Brand: Oriental motor Pages: 52
Opt OPT-DPA1024E-4 Manual preview
OPT-DPA1024E-4
Brand: Opt Pages: 40
Eclipse TRILOGY T500 Series Instruction Manual preview
TRILOGY T500 Series
Brand: Eclipse Pages: 20
Window Master MotorController WCC 310 UL Installation Instructions Manual preview
MotorController WCC 310 UL
Brand: Window Master Pages: 39
SUPMEA SUP-PH8.0 User Manual preview
SUP-PH8.0
Brand: SUPMEA Pages: 32

Brands by name

Popular brands

Load more brands