NEC 240K - LT XGA DLP Projector User Manual Download

Page: 64 / 152

E-64

Removing the PC Card

Press the eject button. The PC card pops out a little. Grasp the edges

of the PC card and pull it out.

NOTE: Do not eject the PC card while its data is being accessed.

USING THE VIEWER

Direction for Inserting the PC Card

The PC card has a top and bottom and must be inserted into the PC card

slot in a specific direction. It cannot be inserted backwards or upside-down.

Attempting to force it into the slot in the wrong direction may break the

internal pin and damage the card slot. Refer to the PC card's operating

instructions for the proper direction of insertion.

PC Card Type

The PC Card slot accepts PCMCIA Type II only.

CAUTION:

•

Do not use CompactFlash type cards except for flash memory cards.

Using a CompactFlash card with the help of a PC card adapter could

cause damage to the CompactFlash card.

•

Back up your PC card's data in case it will need to be restored.

Eject button

Summary of Contents for 240K - LT XGA DLP Projector

























































































































































Search results

Summary of Contents for 240K - LT XGA DLP Projector

Reviews:

Related manuals for 240K - LT XGA DLP Projector

Brands by name

Popular brands

NEC 240K - LT XGA DLP Projector, User Manual

Search results

Summary of Contents for 240K - LT XGA DLP Projector

Reviews:

Related manuals for 240K - LT XGA DLP Projector

Brands by name

Popular brands