NEC 240K - LT XGA DLP Projector User Manual Download

Page: 112 / 152

E-112

USING ON-SCREEN MENU

⬎

Menu Descriptions & Functions

Setting a Password

A password can be set for your projector to avoid operation by an unau-

thorized person.

There are two password options: one for menu and the other for logo.

When a password is set, doing any one of the following four operations will

display the Password input screen.

For Menu:

* Changing the menu to Advanced

* Editing the custom menu

For Logo:

* Changing the background

* Changing the logo data in PC Card Files

Procedures for Password setting apply to both Menu and Logo.

Entry

To assign your password:

NOTE: Up to 15 alphanumeric characters can be assigned.

1. Type a password.

Highlight "Entry" and press the ENTER button.
The "Enter the Password screen" will be displayed.

Make sure that [

] is highlighted and then press the ENTER button.

The Software keyboard appears. Use the Software keyboard to type a password and
then highlight "OK" on the “Enter the Password” screen and press the ENTER button.
The [Confirm Password] screen will be displayed.

2. Type the same password again. Highlight "OK" on the “Enter the Password” screen

and press the ENTER button.

Your password will be assigned.

Summary of Contents for 240K - LT XGA DLP Projector

























































































































































Search results

Summary of Contents for 240K - LT XGA DLP Projector

Reviews:

Related manuals for 240K - LT XGA DLP Projector

Brands by name

Popular brands

NEC 240K - LT XGA DLP Projector, User Manual

Search results

Summary of Contents for 240K - LT XGA DLP Projector

Reviews:

Related manuals for 240K - LT XGA DLP Projector

Brands by name

Popular brands