NDS EndoVue Plus 15" User Manual Download Page 12

Page: 12 / 36

Inputs Menu

When the display is powered on and

Auto Source Select

, then

Auto Source Select

looks at the

previously selected input

rst. If a signal is present it is displayed, otherwise

Auto Source Select

starts

scanning the inputs for a signal. When the display is powered on and

Auto Source Select

off

, the

previously selected input is the only input that the display looks at.

To switch to a different input source, press the

INPUT

button to open the input menu. The Input menu

shows: a

to the left of the active input. Press the

SCROLL

button to highlight the desired input. Finally,

press the

◄

button to select it.

Video Source

Connecting a Video Printer

A video printer may be connected via the

VGA/RGBS

connector

(shown on page 2) or the

S-Video

connector (shown on page 2).

Use the

VGA/RGBS

connector to connect an

RGBS

signal. Select the

VGA/RGBS

from the input menu. The

VGA/RGBS

connector is also used to connect a

YPbPr

signal. Select the

YPbPr

from the input menu.

Do not use the

DVI-I/RGBS

connector.

Summary of Contents for EndoVue Plus 15"





































Search results

Summary of Contents for EndoVue Plus 15"

Reviews:

Related manuals for EndoVue Plus 15"

Brands by name

Popular brands

NDS EndoVue Plus 15", User Manual

Search results

Summary of Contents for EndoVue Plus 15"

Reviews:

Related manuals for EndoVue Plus 15"

Brands by name

Popular brands