background image

Manual 

NBE Pellets Systems 

EXCEPTION FOR PRESSURE EXPANSION

 

NBE 
Jannich Hansen 
Brinken 10 
DK 9830 Oester Vraa                                                        

 

                                                                                                           

 

Landskronegade 33 

                                                                                                          

2100 Copenhagen 

           Telephone 

39152000 

                                                                                                         

www.arbejdstilsynet.dk

 

 

 

 

 

 

 

 

 

 

 

 

Your contact JH 

                                                                                                           

Our ref. 20030027413 

                                                                                                           

Our contact.      

 

 

 

 

 

 

 

 

 

 

 

 

G.Agersnap  

 

 

 

 

 

 

 

 

 

 

 

Direct telephone 

           0045-3915265915 

 

 

Re: Use of burner to burn wooden pellets type Woody, Scotte, Bio-comfort and  
Boink in boiler equipment in relation to smaller, closed facilities in compliance with Work 
Supervisor Regulations for Hot-water Heating Systems. (publ. 42/1980 para 4)

 

 
With regard to your query of 1 September 2006 concerning the use of the burner to burn wooden 
pellets type Woody, Scotte, Bio-comfort and Boink in boiler equipment in relation to smaller, 
closed facilities with pressure expansion, we can report that the Work Supervisor has perused the 
submitted materials and can declare that the burner for wooden pellets type Woody, Scotte, Bio-
comfort and Boink can be installed in the heat facilities listed in paragraph 4 of the Work Supervi-
sor publication no. 42/1980, Regulations for Hot-water Heating Systems. 
 
It is assumed that the boiler contains the requisite amount of water and that the entire heating fa-
cility is designed in exact compliance with the instructions given in publication 42/1980, and also 
that the electricity supply will only be connected to a boiler with a fitted and connected thermostat 
with the appropriate overheating safety fuse which must be manually reconnected after activation. 
 
All heating in the boiler must take place by means of the pellet combustion chamber, and only 
fuels listed in the instructions may be used. Otherwise the equipment must be installed with an 
open expansion (compare paragraph 2 in publication 42/1980). 
 
This decision is based on the enclosed instructions and diagrams, Test Report no. 300-ELAB-
0741, as well as the Power Dropout Test with readings recording the build-up of heat in the boiler 
if the power supply to the equipment is interrupted. 
 
Best regards, 
 
G.Agersnap 

Summary of Contents for Bio Comfort Series

















Reviews: