16
17
User‘s Manual
∆
SJ250ST
∆
Introduction
Dear customer,
Thank you for the confidence you have shown in the Nature7
brand by purchasing this product.
The product has been subjected to comprehensive testing of
reliability, safety and quality in terms of the prescribed norms and
regulations of the European Union.
Contact our customer and consulting centre for any questions at:
Tel.: +420 222 745 130
Fax: +420 225 277 400
www.nature7.eu
Manufacturer: Madal Bal a. s., Průmyslová zóna Příluky 244, CZ-
76001 Zlín, Czech Republic.
Date of issue: 27/04/14
I. Characteristics
The Nature7 SJ250ST screw top, low speed juicer is designed
for juicing rooted and leafy vegetables, fleshy fruits and berries.
Even larger pieces of root vegetables, which are precut before
screw top utilization, can be juiced thanks to the removable and
retractable slicers. The low speed allows for quality pressing of
the flesh, which makes the juice more enriched with vitamins and
valuable compounds.
The appliance is intended for domestic use and not for
commercial service (e.g. in a restaurant).
II. Technical Data
Order number
569502
Type number
SJ250ST
Power
250 W
Revolutions
85 min
-1
Power supply voltage / frequency
220-240 V ~ 50 Hz
Juice extraction
80 %
Insulation class
I
Time of continuous operation
≤ 20 min
Interval length
20-30 min
Weight
5.4 kg
III. Components and
Control Elements
DESCRIPTION OF THE INDIVIDUAL PARTS OF THE
JUICER
(
M
Fig. A)
1) Motor
2) Containers for juice and waste
3) Outlet for juices with flow control
4) Stock tank
5) Sieve embedded within the adjusting sleeve with spatula type
device
6) Screw
7) Removable slicer for pre-cutting root vegetables
8) Stock tank cover with filler neck
9) Dish for sliced vegetables and fruit for subsequent infeed
10) Spile for the infeed of fruit/vegetables by means of the filler
neck to the screw
IV. Juicer Assembly
c
CAUTION
Read carefully the operation manual before assembling and using
the juicer.
The manufacturer is not responsible for product damage or
potential injuries that are caused by improper or careless use of the
juicer.
Include the instructions for use if you lend out or sell on the juicer
and avoid damaging this manual.
8
Thoroughly rinse all parts that shall come into contact
with foodstuffs before the initial use of this product!
1
Make sure that the circular silicone sealing and silicone sealing
plug are in good condition before placing the stock tank to the
juicer motor. Then insert the silicone plug into the waste outlet
opening, otherwise the juice will overflow out of the stock tank
(
M
Fig. B)
.
2
The juicer stock tank rotates as such, that the arrow at the
lower edge of the stock tank is set in the unlatched lock position
on the device body and after it has been set in place, turn it into
the latched lock position.
(
M
Fig. C+D+E)
.
3
The sieve embedded within the adjusting sleeve with spatula
type device rotates as such, that the arrow on the sieve is set in
the marking place on the side of the stock tank, afterwards, it
is possible to set it on the stock tank itself. Make sure that the
adjusting sleeve with spatula type device is correctly fitted in the
stock tank.
(
M
Fig. F+G)
.
4
Insert the screw shaft into the opening in the centre of the
stock tank. When juicing root vegetables and celery stalks into
the screw centre, attach the supplied slicer for pre-cutting (part 7)
(
M
Fig. H)
.
If everything is not aligned correctly, the cover with the filler can not
be screwed into the stock tank.
5
The cover with the filler neck rotates as such, that the
unlatched lock symbol on the cover is at the place of the triangle
on the side of the stock tank. After setting the cover into the stock
tank, the cover is to be turned into the latched lock position
(
M
Fig. I+J+K)
.
c
NOTE
If the juicer system is not assembled and set properly, the motor
cannot be activated due to an interlock switch, that serves
as a protection against damage because of poorly deployed
components.
6
Turning of the silicone sealing position in the outflow status
can regulate the flow
(
M
Fig. L)
.
7
Place containers under the outlet for collecting juices and
wastes and insert the spile into the filler neck. The juicer is now
ready for use
(
M
Fig. M)
.
V. Disassembling the Juicer
System
c
NOTE
Before disassembling, unplug the power cord from the mains.
Proceed in the reverse order of assembly for disassembly steps.
VI. Switch On/Off/Reverse
Before plugging the power cord into the mains, check whether the
mains voltage corresponds to the range of 220-240 V. The device can
be used in this voltage range
The socket must be three-pin (ground), since the juicer is insulation
class I.
(
M
Fig. N)
→
Press the knob to turn on (screw rotation)”ON/OFF”.
→
To turn off, press the same knob.
→
For rotation movement in the opposite direction in case
of blockage hold down the “REV” knob. When you release the
button, the movement stops. For the restoration of the original
direction of rotation, press the “ON / OFF” knob.
8
After pressing the knob, a red indicator light will light up in
the knob.
