manualshive.com logo in svg

Nations N32G43 Series, User Manual

The Nations N32G43 Series User Manual is your essential guide to unlocking the full potential of this incredible product. With easy-to-follow instructions and helpful illustrations, you can confidently navigate every feature and setting. Download your free manual from manualshive.com and explore endless possibilities effortlessly.

Share
Download
background image

Nations Technologies Inc.

Tel

：

+86-755-86309900

Email

：

[email protected]

Address: Nations Tower, #109 Baoshen Road, Hi-tech Park North. 
Nanshan District, Shenzhen, 518057, P.R.China

 

 

267

 / 

631

 

 

 

 

Status registers (TIMx_STS) 

Offset address: 0x10 

Reset value: 0x0000 

 

Bit field 

Name 

Description 

15:13 

Reserved 

Reserved, the reset value must be maintained 

12 

CC4OCF 

Capture/Compare 4 overcapture flag 

See TIMx_STS.CC1OCF description. 

11 

CC3OCF 

Capture/Compare 3 overcapture flag 

See TIMx_STS.CC1OCF description. 

10 

CC2OCF 

Capture/Compare 2 overcapture flags 

See TIMx_STS.CC1OCF description. 

9 

CC1OCF 

Capture/Compare 1 overcapture flag 

This bit is set by hardware only when the corresponding channel is configured in input capture 

mode. Cleared by software writing 0. 

0: No overcapture occurred 

1: TIMx_STS.CC1ITF was already set when the value of the counter has been captured in the 

TIMx_CCDAT1 register. 

8:7 

Reserved 

Reserved, the reset value must be maintained 

6 

TITF 

Trigger interrupt flag 

This bit is set by hardware when an active edge is detected on the TRGI input when the slave 

mode controller is in a mode other than gated. This bit is set by hardware when any edge in 

gated mode is detected. This bit is cleared by software. 

0: No trigger event occurred 

1: Trigger interrupt occurred 

5 

Reserved 

Reserved, the reset value must be maintained 

4 

CC4ITF 

Capture/Compare 4 interrupt flag 

See TIMx_STS.CC1ITF description. 

3 

CC3ITF 

Capture/Compare 3 interrupt flag 

See TIMx_STS.CC1ITF description. 

2 

CC2ITF 

Capture/Compare 2 interrupt flag 

See TIMx_STS.CC1ITF description. 

1 

CC1ITF 

Capture/Compare 1 interrupt flag 

When the corresponding channel of CC1 is in output mode: 

Except in center-aligned mode, this bit is set by hardware when the counter value is the same as 

the compare value (see TIMx_CTRL1.CAMSEL bit description). This bit is cleared by 

software. 

Summary of Contents for N32G43 Series















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for N32G43 Series

Hafele DT 100 Operating Instructions Manual preview
DT 100
Brand: Hafele Pages: 82
Harsco Industrial ENVI Advanced User'S Manual preview
ENVI
Brand: Harsco Industrial Pages: 57
NCR MSR Instructions Manual preview
MSR
Brand: NCR Pages: 8
We Care Solar Suitcase Installation Manual preview
Suitcase
Brand: We Care Solar Pages: 46
Watlow F4T Installation And Troubleshooting User’S Manual preview
F4T
Brand: Watlow Pages: 59
Watts Tekmar WiFi Snow Melting Control 670 Installation Manual preview
Tekmar WiFi Snow Melting Control 670
Brand: Watts Pages: 48
POLA HP49 Handbook preview
HP49
Brand: POLA Pages: 2
HANYOUNG NUX TPR-3N Instruction Manual preview
TPR-3N
Brand: HANYOUNG NUX Pages: 4
Doepke RJSG 1 Installation And Operating Manual preview
RJSG 1
Brand: Doepke Pages: 2
YASKAWA E7N Technical Manual preview
E7N
Brand: YASKAWA Pages: 282
Zareba LIS10 User Manual preview
LIS10
Brand: Zareba Pages: 40
BFT COMPASS SC-RS 232 Installation And User Manual preview
COMPASS SC-RS 232
Brand: BFT Pages: 24
Kamado Joe iKAMAND User Manual preview
iKAMAND
Brand: Kamado Joe Pages: 2
S&P REB 1 Manual preview
REB 1
Brand: S&P Pages: 8
Danfoss AK-PC 420 Instructions Manual preview
AK-PC 420
Brand: Danfoss Pages: 18
iNels SA3-02M Quick Start Manual preview
SA3-02M
Brand: iNels Pages: 14
WAVESTREAM RMC-RRS011-HE01 Operation Manual preview
RMC-RRS011-HE01
Brand: WAVESTREAM Pages: 54
Baldor BC142 Installation And Operation Manual preview
BC142
Brand: Baldor Pages: 33

Brands by name

Popular brands

Load more brands