National Instruments VXIpc 600 Series User Manual Download Page 41

Page: 41 / 88

Appendix B

LED Indicators

B-2

National Instruments Corporation

LEDs and System Startup Cycle

Table B-1 shows a system startup cycle and possible points of failure, up to
and including the state in which the ONLINE LED is asserted.

Table B-1.

LEDs and System Startup Status

Step

LEDs Lit

Status

Possible Problem if

VXI/VMEpc 600 Fails

None

Machine just turned on.

The VXI/VMEpc 600 Series is not
receiving power.

FAIL,
SYSF

Now asserting SYSFAIL because
VXI/VMEbus interface has not
been initialized yet.

Power-on self configuration
(POSC) cannot execute because
of problems with system reset or
because the POSCEN switch is
incorrectly configured.

FAIL,
TEST

VXI/VMEbus interface is being
initialized by MITE power-on self
configuration (POSC) circuitry.

POSC has stalled.

TEST

POSC circuitry has initialized
VXI/VMEbus interface, setting
PASSED and DONE bits.

POSC stalled before clearing the
TEST LED.

None

POSC cycles are complete. VXI
port is ready to respond to Resource
Manager inquiries.

POSC completed successfully;
however, the Resource Manager
either hung or was not executed.

ONLINE

Resource Manager has been
executed, indicating that the VXI
software can now communicate
with the VXI/VMEbus circuitry.

Resource Manager interface
initialized successfully.

Summary of Contents for VXIpc 600 Series

























































































Search results

Summary of Contents for VXIpc 600 Series

Reviews:

Related manuals for VXIpc 600 Series

Brands by name

Popular brands

National Instruments VXIpc 600 Series, User Manual

Search results

Summary of Contents for VXIpc 600 Series

Reviews:

Related manuals for VXIpc 600 Series

Brands by name

Popular brands