National Instruments VXIpc 600 Series User Manual Download | Manualshive

Page: 32 / 88

background image

Chapter 3

Configuration and Installation

VXI/VMEpc 600 Series User Manual

3-12

©

National Instruments Corporation

5.

After saving the configuration, exit Windows and turn off the
computer.

6.

Change jumper W9 to the default position, as shown in Figure 3-11a.

7.

Turn on the computer. If the computer does not boot with this
configuration, you will have to repeat these steps, modifying your
configuration until a final configuration is reached.

Configuring the PC

This section describes how to configure the following options on the PC:

•

SCSI termination

•

System CMOS

•

Ethernet power-on defaults

SCSI Termination

The VXI/VMEpc 600 Series uses active termination on the UW-SCSI bus.
Because the VXI/VMEpc 600 Series is always an end device, you should
not need to disable the termination; however, for informational purposes
Figure 3-12 shows the jumper settings for both enabled and disabled
termination.

Figure 3-12.

SCSI Termination

System CMOS

The VXI/VMEpc-650 contains a backed-up memory used to store BIOS
defaults and configuration information:

Follow this procedure to clear the CMOS contents:

1.

Place the jumper as shown in Figure 3-13b to short the pins of W20,
which is located on the CPU module.

Caution

Do not keep these two pins shorted because the CMOS memory cannot be
sustained when the power is turned off in this state.

a. Terminate SCSI

Signals (Default)

W3

b. Do Not Terminate

SCSI Signals

W3

!

«
...
30
31
32
33
34
...
»

Summary of Contents for VXIpc 600 Series

























































































Reviews:

No comments

Related manuals for VXIpc 600 Series

Brand: Samson Pages: 36

Brand: FBII Pages: 71

Brand: CAME Pages: 4

Brand: ZEHUS Pages: 28

Brand: Valfonta Pages: 12

Brand: Valor Pages: 20

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

Brand: Daktronics Pages: 5

Brand: Daikin Pages: 12

Brand: Farfisa Pages: 20

Brand: Racal Instruments Pages: 64

Brand: IDS Pages: 2

Brand: Lakeshore Pages: 186

Brand: York Pages: 24

FEBCO 860 Small Series

Brand: Watts Pages: 12

Brand: Bardiani Valvole Pages: 54

Brand: Parker Pages: 478

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands