National Instruments VXIpc 600 Series User Manual Download Page 35 | Manualshive

Page: 35 / 88

background image

©

National Instruments Corporation

4-1

VXI/VMEpc 600 Series User Manual

4

BIOS

This chapter contains information on the BIOS (Basic Input Output
System), the low-level interface between the hardware and PC software
that configures and tests your hardware at boot up. The BIOS has an
easy-to-use graphical user interface you use to configure system aspects
according to your needs.

Entering BIOS Setup

To enter the BIOS setup program, perform the following steps:

1.

Turn on or reboot the system. A screen appears with a series of
diagnostic checks.

2.

When

Hit <DEL> if you want to run SETUP

appears,

press the <DEL> key to enter the BIOS setup program.

3.

Choose options with the keyboard. Modify the settings to reflect
system options.

Default BIOS Setup Settings

To restore the default settings while inside the BIOS setup program,
select either Auto Configuration with Optimal Settings or Auto
Configuration with Fail-Safe Settings.

Select the Optimal settings if you want to get maximum performance from
the VXI/VMEpc 600 Series. Fail Safe settings are more conservative
settings.

«
...
33
34
35
36
37
...
»

Summary of Contents for VXIpc 600 Series

























































































Reviews:

No comments

Related manuals for VXIpc 600 Series

Brand: Vacon Pages: 62

Brand: Farris Engineering Pages: 12

Brand: Eastern Times Technology Pages: 4

Brand: Vacon Pages: 18

Brand: QUAD Pages: 17

Brand: fadini Pages: 16

Brand: Hanna Instruments Pages: 54

Brand: Hanna Instruments Pages: 2

Brand: Full Gauge Controls Pages: 3

Brand: Casambi Pages: 2

Brand: Click2Enter Pages: 34

Brand: Delabie Pages: 20

Brand: Linear Technology Pages: 32

Brand: nurse Pages: 24

Brand: Telit Wireless Solutions Pages: 45

Brand: YOKOGAWA Pages: 33

Brand: Grosvenor Pages: 5

Brand: Kelly Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands